SWR Sound SM-1500 manual 1TRS Balanced Jacks

Page 10

Rear Panel

iI. CROSSOVER—(Bi-amplifier control) Sets the frequency at which your signal is split into high and low components. This always affects the Low and High Out {GG and JJ} jacks. This only affects the *LF and *HF speaker Outputs {OO and RR} when *Bi- Amp mode {HH} is selected.

JJ.HIGH OUT—TRS1line level, 1/4" output. Supplies high frequen- cies; useful for connection to an external power amplifier in a bi-amp configuration. NOTE: This output is always active, inde- pendent of the positions of the mode switches {HH and PP}.

KK..Tuner Out—Plug your instrument tuner in here. This TRS1 output can also be used as an always-active, tube-influenced direct output.

LL..IN—An alternate input to input 1 on the front panel; useful for wireless receivers. This input is disabled when a plug is inserted into input 1 on the front panel.

MM..MAIN BREAKERS—Protects the power amplifiers from electri- cal faults and circuit overloads. If a breaker has tripped (button pops out), switch the Power {Z} OFF and allow the unit to cool down. Inspect your speakers, all connections and other equip- ment for damage before pressing each circuit breaker back in to reset them.

NN..POWER CORD SOCKET—Connect the included** power cord to a properly wired AC electrical outlet in accordance with the voltage and frequency ratings specified on the rear panel of your amplifier.

** The SM-1500 uses a heavy duty power cord to supply the high power requirements. To ensure safe operation: If an extension cord is required, use only one extra-heavy gauge cord (10 AWG or heavier) that is no longer than absolutely necessary.

OO..PARALLEL RIGHT (LOW FREQUENCY) SPEAKER OUTPUTS— Connect right channel (or low frequency) speakers to these three jacks in any combination. The total impedance load of these speakers should ideally be 2 ohms and must never be less than 2 ohms. The power handling capacity of these speakers must be at least 750 watts.

The SM-1500 furnishes both 1/4" and Speakon® speaker con- nections. Use the Speakon® jacks whenever possible to take advantage of their superior electrical efficiency and secure connectors. All three jacks on each side are full range and wired in parallel. Read the Speaker Guidelines section below before connecting speakers.

PP.NORMAL / BRIDGE SWITCH—Selects a core mode of opera- tion for the SM-1500 power amplifiers. Each mode uses different speaker outputs and master volumes. Turn OFF the SM-1500 while switching modes and connections. Use the tip of a pen to reach the recessed button:

•  Normal Mode—The power amplifiers operate separately as right and left channels (in Stereo mode {HH}) or as low and high channels (in Bi-Amp mode). In Normal Mode: use the Parallel Right (*LF) and Left (*HF) speaker Outputs {OO and RR} and both Volume knob {Y} sections.

•  Bridge Mode—The power amplifiers are bridged together to operate as one monolithic power block. In Bridge mode: use the one center speaker output {QQ} and the inner Volume {Y} knob alone.

QQ..MONO (BRIDGE) MODE SPEAKER OUTPUT—One Speakon® speaker output jack is available in Bridge Mode. The total impedance load of this speaker(s) should ideally be 4 ohms and must never be less than 4 ohms. The power handling capacity of this speaker(s) must be at least 1500 watts. Read the Speaker Guidelines section below before connecting speakers.

RR..PARALLEL LEFT (HIGH FREQUENCY) SPEAKER OUTPUTS— Connect left channel (or high frequency) speakers to these three jacks in any combination. The total impedance load of these speakers should ideally be 2 ohms and must never be less than 2 ohms. The power handling capacity of these speakers must be at least 750 watts.

1TRS Balanced Jacks

NOTE: Jacks {FF, GG, JJ and KK} are balanced TRS (Tip/Ring/Sleeve) types and are designed

to accept either TRS or TS (Tip/Sleeve) plugs:

Tip=positive (+) Ring=negative (–) and Sleeve=ground.

While standard shielded TS "mono" guitar cables may certainly be used, the use of "stereo" TRS cables may improve signal-to-noise ratio and/or reduce hum, especially when longer connections are required.

10

Image 10
Contents SM-1500 P o r t a n t S a f e t y I n s t r u c t i o n s N s i g n e s d e S é c u r i t é I m p o r t a n t e s C h t i g e S i c h e r h e i t s h i n w e i s e S t r u ç õ e s I m p o r t a n t e s d e S e g u r a n ç a SM-1500 Bass Amplifier Front Panel Normal Mode-the center knob is left master and the outer Ring knob is the right master volumeOuter ring knob is disabled Outer ring knob is the low-frequency level controlRear Panel 1TRS Balanced Jacks Block Diagram Minimum Speaker Ratings Speaker GuidelinesCompatible Speakers Ohm 750W Ohm 450WRack Mounting Tube ReplacementSpecifications Beauty and reliability of your equipmentAmplificador de bajo SM-1500 Panel frontal Boost LEVEL-Ajusta el nivel de realce de la señal Panel trasero 1Conectores TRS balanceados Diagrama de bloques Altavoces compatibles Guía sobre altavocesValores de altavoz mínimos Recambio de la válvula Montaje en rackEspecificaciones técnicas Amplificateur basse SM-1500 Merci davoir choisi lamplificateur basse SWR SM-1500Face avant Face avant Face arrière 1Jacks symétriques stéréo Synoptique Valeurs minimales des enceintes Connexion des enceintesEnceintes compatibles Ohms 750 W Ohms 450 WMontage en Rack Remplacement de la lampeCaractéristiques techniques SM-1500 Amplificatore per Basso Uscite Speaker con connessioni Speakon e jack da 1/4Pannello Frontale Aural Enhancer Direct Box valvolare Pannello PosterioreIntensifier e il circuito EQ Pre o Post 1Connessioni TRS Bilanciate Diagramma a blocchi Diffusori compatibili Guida alla connessione dei diffusoriRequisiti minimi dei diffusori Sostituire la Valvola Installazione a RackSpecifiche SM-1500 Bassverstärker Biamp-Modus mit einstellbarer Crossover-FrequenzVorderseite LEVEL-Regelt die Stärke des Bass Intensifier-EffektsBoost LEVEL-Regelt den Pegel der Signalverstärkung Rückseite 1symmetrische TRS-Buchsen Blockdiagramm Kompatible Boxen BoxenrichtlinienBoxen-Mindestnennwerte Technische Daten RackmontageRöhrenaustausch Alle Schrauben festAmplificador de Baixo SM-1500 Painel Frontal Cias baixas Anel externo é desabilitadoBem como uma D.I. direct box valvulada Volume Geral YPainel Traseiro Tos de equalização1Plugues TRS Balanceados Diagrama Bloco Potência máxima de saída do amplificador ConfiguraçõesAlto-falantes Compatíveis Especificações Mínimas para Alto-FalantesSubstituição de Válvulas Colocação em um RackEspecificações この度は、SWR SM-1500ベース・アンプリファイアーをお買い上げいただき、 ありがとうございます。 フロントパネル Boost LEVEL(ブースト・レベル)̶ 信号のブースト量を調節します。 リアパネル 1TRSバランス・ジャック ブロック・ダイアグラム スピーカー・ガイドライン ラックマウント SWR

SM-1500 specifications

The SWR Sound SM-1500 is a powerful and versatile bass amplifier that has gained popularity among both amateur and professional musicians. Known for its robust build and high fidelity sound, the SM-1500 is designed to meet the demands of live performances and studio recordings alike.

One of the standout features of the SM-1500 is its impressive power output. With a robust 1500 watts of power, this amplifier is capable of driving even the most demanding speaker cabinets. This ensures that musicians can achieve the necessary volume levels without compromising on sound quality. The amp's power capabilities make it suitable for a wide range of performance venues, from intimate clubs to large concert halls.

The SM-1500 utilizes advanced technology to produce a clear and punchy sound. Equipped with a comprehensive EQ section, this amplifier allows users to tailor their tone precisely. The four-band EQ includes adjustable controls for low, mid, mid-high, and presence frequencies. This flexibility enables musicians to shape their sound, whether they’re aiming for a punchy slap bass tone or a smooth, warm sound.

In addition to its power and EQ capabilities, the SM-1500 features an onboard compressor. This technology helps to smooth out dynamic range, ensuring that both soft and loud notes are balanced while maintaining clarity and articulation. The built-in limiter also protects the amplifier and speakers from potential damage due to signal clipping, which is essential during high-energy performances.

Portability is another significant aspect of the SM-1500. Despite its powerful output, it is designed with a relatively lightweight and compact chassis, making it easy to transport. This is a crucial factor for touring musicians who need reliable equipment that doesn't add excessive weight to their gear load.

The SM-1500 also includes multiple input options, accommodating both passive and active bass guitars. This versatility ensures compatibility with various instruments, providing musicians with the freedom to explore different sounds and styles.

In conclusion, the SWR Sound SM-1500 is a formidable bass amplifier that combines power, precision, and portability. Its advanced technology, user-friendly features, and flexible sound shaping options make it a top choice for bassists looking to elevate their sound in any performance setting. Whether in the studio or on stage, the SM-1500 is built to deliver an exceptional auditory experience.