TANDBERG D5016402 user manual Appendix 3 Connecting to PRI/T1, Using CSU adapter

Page 98

Appendix

TANDBERG Director Videoconferencing System

 

 

Appendix 3: Connecting to PRI/T1

Using CSU adapter

Connecting the system to the ISDN network via the E1/T1-interface using an Adtran T1 ESF CSU ACE will allow up to 1.54 Mbps transmission. The E1/T1-interface must be connected to a CSU approved according to IEC 60950, UL 1950 or equivalent standard.

NOTE: The PRI-line will run the AT&T 4ESS, 5ESS and National ISDN protocols in addition to Euro ISDN (E1).

Wall

Adtran

CSU PRI-interface

NET* CPE*

Director

ISDN E1/T1 (1)

ISDN E1/T1 (2)

Director

ISDN E1/T1 (1)

*RJ-48C type interface

Connecting to Adtran T1 ESF CSU ACE

Connect the PRI cable from the Codec to the input marked CPE on the Adtran CSU (straight through category 5 cable is recommended). Connect to the network via the NET connector on the Adtran CSU. When two Codecs are cascaded, connect the second Codec to the E1/T1 port 2 on the first Codec using a T1 crossover cable.

Configuration of the system

Press MENU on the remote control. Select ‘Terminal Settings’, ‘Network’.

Select ‘Current Network: PRI’ and specify your PRI number, max. channels, cable length (between Codec and CSU) and switch type:

N O T E

CASCADED CONNECTION:

REMEMBER TO PROGRAM

NUMBERS AND MSN.

OTHERWISE, THE FIRST CODEC

WILL ANSWER ALL CALLS.

Configuration of Adtran T1 ESF CSU ACE

Enter ‘2)CONFIG’ menu using SCROLL and ENTER buttons.

Enter ‘3)TERMINAL’ menu. Check ‘1)FORMAT:ESF’, ‘2)CODE: B8ZS’ , ‘3)SET LBO: 0-133’ (Corresponding to ‘Cable Length’ setting on the Codec.

Go to main menu and enter ‘1)NETWORK’ menu. ‘7)SET LBO: 0.0 (According to information from Telco).

Also, other network parameters should be set according to information from your Telco.

98

Image 98
Contents Director Page Disclaimer Environmental IssuesTrademarks and copyright Production of productsOther Warnings and Safety Precautions Important InformationTandberg Director Videoconferencing System Contents Tandberg Director Videoconferencing System Introduction Welcome to the Tandberg DirectorAt a Glance The Tandberg Director WaveAudio and Video Sources System OverviewControl Interface Optional Equipment System Connections Rear Interface PanelRear Interface Panel Connections Rear Interface Panel A/V Plate Installation & Setup Room ConfigurationInstalling the Guest Laptop Shelf Guest laptop shelfInstalling the Adjustable Camera Shelf To install the videoconferencing shelfT E Tandberg Director Videoconferencing System Camera S-VID OUT Camera Ctrl OUT Smart BoardTM Projector Setup and Calibration Powering on the SystemSystem Setup Touchscreen Calibration Touch Panel Tools for System Configuration System InformationIR Functions AudioEdit Directory Update DirectorySystem Options Other Networks Using the External Network Interface Network ConnectionsTouch Panel Device ConnectionsMicrophone Main CameraPC and Laptop Computer Setup LaptopPC Calibration Control Orientation Getting StartedSystem startup Touch Screen and Remote IR Controls ‘IR Controls’ will appear in the place of the ‘Address Book’ Codec Basics Menu structureGeneral Codec Configuration LAN configuration Network and LAN SettingsIsdn configuration DUOVideoTF Mode Microphone on/off Adjusting volumeGeneral use DirectoryProjector Standby Button LEDMultiSiteTF MCU LAN 3MBEstablishing MultiSiteTF meetings using Directory MultiSiteTF cascadingText Chat / Closed Captioning PC SoftPresenterWeb-interface StreamingScreen Basics Display OperationLocal Display Operation Source Selection Device ControlTaskbar Video Display WindowMaking Calls When the Director receives/initiates a video/audio callVideoconference Operation Speed DialingWill attempt to call the last manually dialed number Disconnecting a CallManual Dialing Back button to exit from this screenEditing Speed Dial Directory Creating a new speed dial numberEditing an existing speed dial number On Screen SymbolsMaking a MultiSiteTF Call Videoconference Main Screen Video Window Display ControlVideoconferencing Taskbar PIPFar End Camera Control Source DuoVideoTF OperationTask23456789Bar Multipoint OperationMain menu Menu PasswordAdvanced use Video VGA ResolutionsCall quality Natural VideoAdvanced call quality Presentations Presentation ModeDuoVideo Mode DuoVideo QualityUtilities Welcome Menu Dual MonitorAuto-PIP Continuous PresenceMCU services Quick MenuTerminal Names Request floorRelease floor View site #Chair control Audio Settings Audio InputsMix Mode Level Settings InputsLevel Settings Outputs Audio OutputsRoom Size Echo ControlNoise Reduction MotionAutomatic Gain Control AGC Settings Tips for improving the echo canceller performanceRestore Audio Defaults Video SettingsAlert Tones & Volume Camera Tracking ModeWhitebalance FocusBrightness VGA Out VGA SettingsVideo Name VGA Out QualityStart using VNC VNC SettingsPassword AddressTerminal Settings Network ConfigurationLine setup ISDN-BRI SettingsIsdn switch type Advanced Isdn settings Subaddress ExampleISDN-PRI Settings PRI Switch Type Channel HuntingAdvanced ISDN-PRI Settings Line SettingsAdvanced Isdn Settings Max Channels Leased E1/T1 SettingsNetwork Interface Start ChannelExternal network settings Call controlCable Specification 35/RS-366 cable Network clockingTTL/Router Hops LAN SettingsAddress Port Allow Remote Start How to view streamingStreaming Source AnnouncementsSettings Advanced H.323 Settings IP Precedence IP Type of Service TOSTells the router to minimize the delay Tells the router to maximize the reliabilityIP Settings Incoming MCU calls Call SettingsSnmp Settings Snmp Trap HostFallback to telephony Access CodeIncoming telephone calls Encryption Secure ConferenceNetwork Profiles Encryption ModeMax Call Length Dataport configuration DataportFollowing options are available LanguageSoftware Options Channel status DiagnosticsSystem info Call status Cause codesFar End Loop Isdn only Restore defaultsView Current Settings System SelftestAppendices Configuring Appendix 1 Connecting to Isdn using network adaptersConnecting Configuration of Telesync Adapter Appendix 2 Connecting to the Switched 56 networkUsing Telesync TS-256 SW56/ISDN adapter Configuration of the systemConnecting to Adtran T1 ESF CSU ACE Appendix 3 Connecting to PRI/T1Using CSU adapter Configuration of Adtran T1 ESF CSU ACEAppendix 4 Environmental & operational considerations Guidelines for Optimal Videoconferencing EnvironmentsBackground Brightness Control Loudspeaker VolumeIris Control and Lighting Appendix 5 Using the file system Description of the different filesStreaming Password Access CodeMenu Password IP PasswordEncryption ServicesSnmp Security alert Appendix 7 12 Touch Panel Interface Local Display Operation105 106 2323 Videoconference Operation234 2345678 Video Features Technical Description111 Abbreviations Symbols Index114 115 Servicing Canada