Southbend STRG-5D, STRG-3D manual Attach Legs, Unpacking

Page 14

INSTALLATION

STRATOSTEAM COUNTERTOP STEAMER

STEP 1: UNPACKING

IMMEDIATELY INSPECT FOR SHIPPING DAMAGE

All containers should be examined for damage before and during unloading. The freight carrier has assumed responsibility for its safe transit and delivery. If damaged equipment is received, either apparent or concealed, a claim must be made with the delivering carrier.

Apparent damage or loss must be noted on the freight bill at the time of delivery. The freight bill must then be signed by the carrier representative (Driver). If the bill is not signed, the carrier may refuse the claim. The carrier can supply the necessary forms.

A request for inspection must be made to the carrier within 15 days if there is concealed damage or loss that is not apparent until after the equipment is uncrated. The carrier should arrange an inspection. Be certain to hold all contents plus all packing material.

Do the following:

1.Cut the banding straps and remove the corrugated cardboard surrounding the steamer. If legs were shipped in the same container, set them aside for installation in later steps of this procedure. Do not remove any tags or labels attached to the steamer until the steamer is installed and working properly.

2.If the steamer was shipped on a wooden skid, cut the banding strap holding the steamer to the wooden skid, unbolt the shipping hold-down brackets from the skid, then remove the brackets from the steamer.

3.If the steamer is to be installed on legs, go to Step 2a.

If the steamer is to be installed without legs on a countertop, go to Step 2b. If the steamer is to be mounted on the optional cabinet base, go to Step 2c. If two steamers are to be stacked, go to Step 2d.

STEP 2A: ATTACH LEGS

A set of four legs is packed with steamers ordered with legs.

A threaded hole is located at each corner. Each leg has a corresponding mating thread. The legs can be adjusted to overcome a slightly uneven surface.

1.Raise the steamer sufficiently to allow the legs to be attached. For safety, “shore up” and support the steamer with an adequate blocking arrangement strong enough to support the load.

2.Screw the legs into the holes (see Figure 4). Note that the front legs are different than the rear legs.

3.Lower the steamer gently onto a level surface. Never drop or allow the steamer to fall.

4.Make sure that the steamer is level (both side-to-side and front-to-back). If necessary, adjust the height of each leg by turning the foot-pad of the leg.

5.Go on to Installation Step 3.

Figure 4

Attach Legs

PAGE 14 OF 50

OWNER’S MANUAL 1185290

Page 13 Page 15
Image 14
Page 13 Page 15
Contents StratoSteam Countertop Steamer Safety Precautions Introduction Location of Serial PlatesDimensions ClearancesDimensions Water Requirements Electrical RequirementsGAS Pressure Requirements Drain RequirementsOperation Troubleshooting by OperatorStartup ShutdownTimer ControlsCooking Tips Suggested Cooking Times Cleaning & Maintenance Daily Cleaning and MaintenancePeriodic DE-LIMING AS Needed STAINLESS-STEEL SurfacesInstallation Attach Legs Attach LegsUnpacking Mounting on Cabinet Base Installation on CountertopAttach to Countertop Stacking TWO SteamersLocation of Connections and Vents Drain ConnectionWater Connection Water DrainWater Connection Testing the GAS Supply Piping GAS ConnectionElectrical Connection Check Steamer Operation Check the InstallationSHUT-DOWN and WIPE-CLEAN Steamer Service Troubleshooting FLOWCHARTS, PROCEDURES, and Wiring Diagrams HOW the Steamer OperatesHow the Steamer Operates Steamer Not Heating Up, Power Light Is Not Lit Disconnect Power AT Circuit BreakerCheck that water-supply pressure is adequate Buzzer Does Not Come On When Timer Runs Out Hot Surface Ignitor Glows Red, But Burners Not On Hot Surface Ignitor Does Not Glow Red Not All Burners Ignite Burner Lights But Goes Out Within a Few Seconds Symptom Possible Cause Cure Power Switch Check Disconnect Power AT Circuit BreakerTimer and Buzzer Check Door Switch Check High-Limit Thermostats Check Water Solenoid Check Wiring Diagram for 208/220/240 Volt and 115 Volt Models Parts Diagram PartsStructural Parts See parts list on previous Door Assembly Parts Door Switch Parts Control Panel Parts Burner Assemblies, Thermocouple, and Ignition Module Water Train Parts Water-Train Parts Cabinet Base Parts Cabinet-Base Parts Stratosteam Countertop Steamer StratoSteam Countertop Steamer Models STRG-3D STRG-5D
Top Page Image Contents