Woods Equipment S22CD, S20CD, S15CD Safety & Instructional Decals, Replace Immediately If Damaged

Page 10

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

1- YELLOW REFLECTOR PN 20034004

2- RED REFLECTOR PN 57123

4- RED-ORANGE FLUORESCENT MATERIAL PN 20034034

5 - PN 50030977

3 - SERIAL NUMBER PLATE

MODEL NO.

SERIAL NO.

 

Woods Equipment Company

 

Oregon, Illinois, U.S.A.

 

CAUTION

 

PRECAUCION

1.

Read Operator's Manual before starting.

1.

Lea el Manual del Operario antes de empezar.

2.

Stop tractor engine, place all controls in

2.

Pare el motor del tractor, ponga todos los controles en

 

neutral, lower machine to the ground, set

 

neutro, baje la máquina hasta el suelo, ponga el freno de

 

park brake, remove ignition key, and wait

 

estacionamiento, quite la llave del encendido, y espere a

 

for all moving parts to stop before

 

que todas las pizas móviles hayan parado antes de dar

 

servicing, adjusting, repairing, or

 

servicio, hacer ajustes, reparaciones, o de desatascar.

 

unplugging.

3.

Mantenga cerrados y asegurados todos los protectores y

 

 

3.

Keep all guards and access doors closed

 

las compuertas antes de poner a funcionar la máquina.

 

and secured before operating.

4.

Mantenga retirados de las piezas móviles, las manos, los

 

 

4.

Keep hands, feet, hair, and clothing away

 

pies, el pelo, y la ropa.

 

from moving parts.

5.

No permita que nadie vaya con usted en la máquina.

 

 

5.

Do not allow riders.

6.

No entre en el área del rotor mientras el motor está en

 

 

6.

Do not enter rotor area when engine is

 

marcha.

 

running.

7.

Nunca exceda 32 km/h (20 MPH) al transportar.

 

 

7.

Never exceed 20 MPH when transporting.

8.

Use luces intermitentes de aviso cuando viaja con la

 

 

8.

Use hazard flashers when transporting.

 

máquina.

9.

Use drawbar pin with retainer and attach

9.

Use el pasador de la barra de tiro con fiador y enganche la

 

safety chain.

 

cadena de seguridad.

10.

Wear appropriate hearing protection for

10.

Use un protector apropiado para los oidos cuando esté

 

prolonged exposure to excessive noise.

 

expuesto a ruido excesivo por un tiempo prolongado.

11.

Review safety information periodically

11.

Repase la información de seguridad periódicamente

 

prior to use.

 

antes del uso.

50030977-B

10 Safety

MAN0506 (Rev. 9/5/2008)

 

 

Image 10
Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation Safety RulesTraining Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordBREAK-IN of the Flail Shredder OperationPrincipal Components After operating for 1/2 hourPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorPTO Driveline Length With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Attach PTO Driveline Without Quick Hitch AttachmentPull-Type Model Attach Hydraulics Center Cutter OptionPreparing for Operation Raise StandsRemoving Shredder from Tractor Flail HeightPull-Type Models SET Operating HeightPoint Hitch Models Point & 2-Point Hitch ModelsStarting the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Stopping the TractorGround Speed CleaningHazard Area TurningAdditional Rear Wheels Rubber FlapsBED Cones Greasing Service & MaintenanceLubricants Lubrication ScheduleLubrication Points Every 40 hours of operation Daily or every 8 hours of operationEvery 25 hours of operation AnnuallyHours or daily Lubrication Service Record Hours Serviced byGearbox OIL Leakage HoursGearbox leakage & Troubleshooting Changing Gearbox OILWheel Spacing Ratchet Height AdjustmentReplacing Flail Knives Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsBreaking In the Clutch Run Replacing Stub ShaftServicing Weasler Modular Friction Clutch Removing the DrivelineRebuilding Overrunning Clutch Rebuilding Friction PackMounting Clutch to Shredder Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Dealer SET-UP Instructions AssemblyWheel Assembly For Some Models Shipped on EndALL Units PULL-TYPE Hitch InstallationPull-type units only Rubber Flap Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowBlock Shredded Center CUT KIT InstallationAssemble Motor and Blade Install Motor Housing Assembly HosesConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois