Woods Equipment S20CD, S22CD, S15CD, S27CD, S25CD manual Worksheet for Contour Flail Patterns

Page 36

WORKSHEET FOR CONTOUR FLAIL PATTERNS

36 Contour Flail Patterns

MAN0506 (Rev. 9/5/2008)

 

 

Image 36
Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationSafety Rules PreparationTraining Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation Principal ComponentsBREAK-IN of the Flail Shredder After operating for 1/2 hourHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Without Quick Hitch Attachment Pull-Type ModelAttach PTO Driveline Attach Hydraulics Center Cutter OptionRaise Stands Removing Shredder from TractorPreparing for Operation Flail HeightSET Operating Height Point Hitch ModelsPull-Type Models Point & 2-Point Hitch ModelsSetting Flail Height Setting Outer Trailing Wheels Casters & StrutsStarting the Tractor Stopping the TractorCleaning Hazard AreaGround Speed TurningRubber Flaps Additional Rear WheelsBED Cones Service & Maintenance LubricantsGreasing Lubrication ScheduleLubrication Points Daily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation AnnuallyLubrication Service Record Hours Serviced by Gearbox OIL LeakageHours or daily HoursGearbox leakage & Troubleshooting Changing Gearbox OILRatchet Height Adjustment Wheel SpacingReplacing Flail Knives Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsReplacing Stub Shaft Servicing Weasler Modular Friction ClutchBreaking In the Clutch Run Removing the DrivelineRebuilding Friction Pack Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Assembly Wheel AssemblyDealer SET-UP Instructions For Some Models Shipped on EndPULL-TYPE Hitch Installation ALL UnitsPull-type units only Manual Storage Tube Installation Optional Equipment Rubber Belting InstallationRubber Flap Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowCenter CUT KIT Installation Block ShreddedAssemble Motor and Blade Install Motor Housing Assembly HosesInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDealer Check Lists PRE-DELIVERY Check ListDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap Bolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois