Woods Equipment S20CD, S22CD, S15CD Install Center Deflector, Safety Light Kit Diagram Non-End Tow

Page 41

provided. Make sure that light lenses are in the correct position in relation to direction of equipment travel: amber lenses on the outside, red lenses on the inside facing rear of shredder.

3.Install light bracket on end of shredder using 1/2 NC x 1-1/2" hex bolts, washers and nuts (four each) in slots 3 and 4 on top of end sheet.

4.Plug ends of wiring harness into corresponding plugs of the light units (Note: left side of wishbone harness is labeled “Left”).

5.Run wiring harness along top of shredder and secure with enclosed adhesive-backed clamps (5) approximately every two feet.

6.Connect 7-pin connector of wiring harness to tractor and test all light functions before actual use.

5.Dual lamp, 4-pin LH

6.Dual lamp, 4-pin RH

8.Clamp, adhesive-backed

9.1/4 NC x 1" Hex bolt

10.1/4 NC Hex nut

11.1/4" Lock washer

12.1/4" Flat washer

20.Wiring harness

21.Dual light bracket

Figure 49. Safety Light Kit Diagram (Non-End Tow)

Figure 50. Safety Light Installed - Rear View

Figure 51. Safety Light Installed - Front View

Install Center Deflector

Slide deflector (1) between shredder center channel with the point forward.

Secure into position using four 1/2 NC x 1-1/4 carriage bolts (2) and flange lock nuts (3).

3 2

DP3

1

1.Center deflector

2.1/2 NC x 1-1/4 carriage bolt

3.1/2 NC Flange lock nut

Figure 52. Center Deflector Installed

MAN0506 (Rev. 9/5/2008)	Assembly 41

Image 41

Contents Flail Shredder Introduction LEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementTraining Safety RulesPreparation Transportation OperationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordPrincipal Components OperationBREAK-IN of the Flail Shredder After operating for 1/2 hourTractor Weight HorsepowerPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Pull-Type Model Without Quick Hitch AttachmentAttach PTO Driveline Attach Hydraulics Center Cutter OptionRemoving Shredder from Tractor Raise StandsPreparing for Operation Flail HeightPoint Hitch Models SET Operating HeightPull-Type Models Point & 2-Point Hitch ModelsSetting Outer Trailing Wheels Casters & Struts Setting Flail HeightStarting the Tractor Stopping the TractorHazard Area CleaningGround Speed TurningBED Cones Rubber FlapsAdditional Rear Wheels Lubricants Service & MaintenanceGreasing Lubrication ScheduleLubrication Points Every 25 hours of operation Daily or every 8 hours of operationEvery 40 hours of operation AnnuallyGearbox OIL Leakage Lubrication Service Record Hours Serviced byHours or daily HoursChanging Gearbox OIL Gearbox leakage & TroubleshootingReplacing Flail Knives Ratchet Height AdjustmentWheel Spacing Servicing Rotors Flail Tubes Replacing Rubber Shield FlapsReplacing Components Removing ComponentsServicing Weasler Modular Friction Clutch Replacing Stub ShaftBreaking In the Clutch Run Removing the DrivelineMounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Problem Cause Solution TroubleshootingWorksheet for Contour Flail Patterns 24’ Wheel Assembly AssemblyDealer SET-UP Instructions For Some Models Shipped on EndPull-type units only PULL-TYPE Hitch InstallationALL Units Optional Equipment Rubber Belting Installation Manual Storage Tube InstallationRubber Flap Installation Safety Light KIT InstallationSafety Light Kit Diagram Non-End Tow Install Center DeflectorAssemble Motor and Blade Center CUT KIT InstallationBlock Shredded Assembly Hoses Install Motor HousingInstall Decals Install Hose ClampsConnect Hoses to Tractor Remove Deflector KitDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch AssemblyWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListRubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Abbreviations Bolt Size ChartIndex AssemblyWarranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company