Woods Equipment S27CD Bolt Torque Chart, SAE Series Torque Chart, Metric Series Torque Chart

Page 63

BOLT TORQUE CHART

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.

Fasteners must always be replaced with the same grade as specified in the manual parts list.

Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.

All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.

SAE SERIES

A TORQUE

CHART

SAE Bolt Head

Identification

SAE Grade 2	SAE Grade 5	SAE Grade 8
(No Dashes)	(3 Radial Dashes)	(6 Radial Dashes)

A					MARKING ON HEAD

			SAE 2			SAE 5			SAE 8
Diameter	Wrench		SAE 2			SAE 5			SAE 8
Diameter	Wrench
(Inches)	Size	lbs-ft		N-m	lbs-ft		N-m	lbs-ft		N-m

1/4"	7/16"	6		8	10		13	14		18

5/16"	1/2"	12		17	19		26	27		37

3/8"	9/16"	23		31	35		47	49		67

7/16"	5/8"	36		48	55		75	78		106

1/2"	3/4"	55		75	85		115	120		163

9/16"	13/16"	78		106	121		164	171		232

5/8"	15/16"	110		149	170		230	240		325

3/4"	1-1/8"	192		261	297		403	420		569

7/8"	1-5/16"	306		416	474		642	669		907

1"	1-1/2"	467		634	722		979	1020		1383

METRIC SERIES

ATORQUE

CHART

8.8	Metric Bolt Head	10.9
Metric	Identification	Metric
Metric		Metric
Grade 8.8		Grade 10.9

			Coarse Thread					Fine Thread
A											A
A			Marking on Head					Marking on Head			A
			Marking on Head					Marking on Head
Diameter &											Diameter &
Diameter &		Metric 8.8		Metric 10.9			Metric 8.8		Metric 10.9		Diameter &
Thread Pitch	Wrench	Metric 8.8		Metric 10.9			Metric 8.8		Metric 10.9		Thread Pitch
Thread Pitch	Wrench										Thread Pitch
(Millimeters)	Size	N-m	lbs-ft	N-m	lbs-ft		N-m	lbs-ft	N-m	lbs-ft	(Millimeters)

6 x 1.0	10 mm	8	6	11	8		8	6	11	8	6 x 1.0

8 x 1.25	13 mm	20	15	27	20		21	16	29	22	8 x 1.0

10 x 1.5	16 mm	39	29	54	40		41	30	57	42	10 x 1.25

12 x 1.75	18 mm	68	50	94	70		75	55	103	76	12 x 1.25

14 x 2.0	21 mm	109	80	151	111		118	87	163	120	14 x 1.5

16 x 2.0	24 mm	169	125	234	173		181	133	250	184	16 x 1.5

18 x 2.5	27 mm	234	172	323	239		263	194	363	268	18 x 1.5

20 x 2.5	30 mm	330	244	457	337		367	270	507	374	20 x 1.5

22 x 2.5	34 mm	451	332	623	460		495	365	684	505	22 x 1.5

24 x 3.0	36 mm	571	421	790	583		623	459	861	635	24 x 2.0

30 x 3.0	46 mm	1175	867	1626	1199		1258	928	1740	1283	30 x 2.0

Typical Washer	Flat Washer
Installations	Lock Washer
Bolt
	8/9/00

Bolt Torque & Size Charts (Rev. 3/28/2007)

Appendix 63

Image 63

Contents Flail Shredder Introduction LEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementSafety Rules PreparationTraining Transportation OperationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordAfter operating for 1/2 hour OperationPrincipal Components BREAK-IN of the Flail ShredderChoosing the Correct Tractor HorsepowerTractor Weight PRE-OPERATION Check ListPTO Driveline Length Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Attach Hydraulics Center Cutter Option Without Quick Hitch AttachmentPull-Type Model Attach PTO DrivelineFlail Height Raise StandsRemoving Shredder from Tractor Preparing for OperationPoint & 2-Point Hitch Models SET Operating HeightPoint Hitch Models Pull-Type ModelsStopping the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Starting the TractorTurning CleaningHazard Area Ground SpeedRubber Flaps Additional Rear WheelsBED Cones Lubrication Schedule Service & MaintenanceLubricants GreasingLubrication Points Annually Daily or every 8 hours of operationEvery 25 hours of operation Every 40 hours of operationHours Lubrication Service Record Hours Serviced byGearbox OIL Leakage Hours or dailyChanging Gearbox OIL Gearbox leakage & TroubleshootingRatchet Height Adjustment Wheel SpacingReplacing Flail Knives Servicing Rotors Flail Tubes Replacing Rubber Shield FlapsReplacing Components Removing ComponentsRemoving the Driveline Replacing Stub ShaftServicing Weasler Modular Friction Clutch Breaking In the Clutch RunRebuilding Friction Pack Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Problem Cause Solution TroubleshootingWorksheet for Contour Flail Patterns 24’ For Some Models Shipped on End AssemblyWheel Assembly Dealer SET-UP InstructionsPULL-TYPE Hitch Installation ALL UnitsPull-type units only Safety Light KIT Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Rubber Flap InstallationSafety Light Kit Diagram Non-End Tow Install Center DeflectorCenter CUT KIT Installation Block ShreddedAssemble Motor and Blade Assembly Hoses Install Motor HousingRemove Deflector Kit Install Hose ClampsInstall Decals Connect Hoses to TractorDealer Check Lists PRE-DELIVERY Check ListDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch AssemblyWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListRubber Flap Bolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart Abbreviations Bolt Size ChartIndex AssemblyWarranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company