Woods Equipment S25CD, S22CD, S20CD Install Hose Clamps, Connect Hoses to Tractor, Install Decals

Page 44

Install Hose Clamps

1.Place hose clamps (36) around hoses (11) and center hoses between center plate.

2.Mark clamp holes in desired location on shedder body and drill two 11/32" holes.

3.Secure hose clamps to shredder using 5/16 NF x 1-1/4 cap screws (20), flat washers (33), lock washers (34) and hex nuts (35). See Figure 57.

Figure 57. Hose Clamp Installation

Connect Hoses to Tractor

NOTICE

■Oil flow to hydraulic motor must not exceed 28 gpm.

1.Connect PRESSURE hose to a tractor rear remote quick coupler that has a lever (handle) that can be placed in the detent or locked position.

2.RETURN hose must be connected directly to the tractor reservoir or to a specifically designated motor return or ‘zero’ back pressure port.

Install Decals

Apply safety decals (24 & 25) to a clean surface on the back of the shredder where they can be seen with out obstructions. Install decals (25) on either side of the hose assembly. See Figure 57.

Remove Deflector Kit

1022652 deflector kit must be removed from the shred- der before using cutter kit. Deflector kit pushes material away from the cutter kit and preventing material from being cut.

44 Assembly	MAN0506 (Rev. 9/5/2008)

Image 44

Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationTraining Safety RulesPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation Principal ComponentsBREAK-IN of the Flail Shredder After operating for 1/2 hourHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Without Quick Hitch Attachment Pull-Type ModelAttach PTO Driveline Attach Hydraulics Center Cutter OptionRaise Stands Removing Shredder from TractorPreparing for Operation Flail HeightSET Operating Height Point Hitch ModelsPull-Type Models Point & 2-Point Hitch ModelsSetting Flail Height Setting Outer Trailing Wheels Casters & StrutsStarting the Tractor Stopping the TractorCleaning Hazard AreaGround Speed TurningBED Cones Rubber FlapsAdditional Rear Wheels Service & Maintenance LubricantsGreasing Lubrication ScheduleLubrication Points Daily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation AnnuallyLubrication Service Record Hours Serviced by Gearbox OIL LeakageHours or daily HoursGearbox leakage & Troubleshooting Changing Gearbox OILReplacing Flail Knives Ratchet Height AdjustmentWheel Spacing Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsReplacing Stub Shaft Servicing Weasler Modular Friction ClutchBreaking In the Clutch Run Removing the DrivelineMounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Assembly Wheel AssemblyDealer SET-UP Instructions For Some Models Shipped on EndPull-type units only PULL-TYPE Hitch InstallationALL Units Manual Storage Tube Installation Optional Equipment Rubber Belting InstallationRubber Flap Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowAssemble Motor and Blade Center CUT KIT InstallationBlock Shredded Install Motor Housing Assembly HosesInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois