Woods Equipment S27CD, S22CD, S20CD, S15CD, S25CD manual Operator Record, Operator SIGN-OFF Record

Page 13

OPERATOR SIGN-OFF RECORD

Woods Equipment Company follows the general safety standards specified by the American Society of Agri- cultural and Biological Engineers (ASABE) and the Occupational Safety and Health Administration (OSHA) for agricultural equipment.

Anyone who will be operating and/or maintaining the flail shredder must read and clearly understand all Safety, Operating, and Service & Maintenance infor- mation presented in this manual.

.

Do not operate or allow anyone else to operate this equipment until this information has been reviewed. Review this information annually, before the season start-up. Make periodic reviews of the Safety and Operation sections standard practice for those using any of your equipment.

Use the following Operator Sign-off Record to verify that each operator has read and understood the infor- mation in this manual and has been instructed in the safe operation of the flail shredder.

DATE

OPERATOR’S NAME (PRINT)

OPERATOR’S SIGNATURE

MAN0506 (Rev. 9/5/2008)	Operator Record 13

Image 13

Contents Flail Shredder Introduction LEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementPreparation Safety RulesTraining Transportation OperationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordPrincipal Components OperationBREAK-IN of the Flail Shredder After operating for 1/2 hourTractor Weight HorsepowerPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Pull-Type Model Without Quick Hitch AttachmentAttach PTO Driveline Attach Hydraulics Center Cutter OptionRemoving Shredder from Tractor Raise StandsPreparing for Operation Flail HeightPoint Hitch Models SET Operating HeightPull-Type Models Point & 2-Point Hitch ModelsSetting Outer Trailing Wheels Casters & Struts Setting Flail HeightStarting the Tractor Stopping the TractorHazard Area CleaningGround Speed TurningAdditional Rear Wheels Rubber FlapsBED Cones Lubricants Service & MaintenanceGreasing Lubrication ScheduleLubrication Points Every 25 hours of operation Daily or every 8 hours of operationEvery 40 hours of operation AnnuallyGearbox OIL Leakage Lubrication Service Record Hours Serviced byHours or daily HoursChanging Gearbox OIL Gearbox leakage & TroubleshootingWheel Spacing Ratchet Height AdjustmentReplacing Flail Knives Servicing Rotors Flail Tubes Replacing Rubber Shield FlapsReplacing Components Removing ComponentsServicing Weasler Modular Friction Clutch Replacing Stub ShaftBreaking In the Clutch Run Removing the DrivelineRebuilding Overrunning Clutch Rebuilding Friction PackMounting Clutch to Shredder Service & Maintenance Problem Cause Solution TroubleshootingWorksheet for Contour Flail Patterns 24’ Wheel Assembly AssemblyDealer SET-UP Instructions For Some Models Shipped on EndALL Units PULL-TYPE Hitch InstallationPull-type units only Optional Equipment Rubber Belting Installation Manual Storage Tube InstallationRubber Flap Installation Safety Light KIT InstallationSafety Light Kit Diagram Non-End Tow Install Center DeflectorBlock Shredded Center CUT KIT InstallationAssemble Motor and Blade Assembly Hoses Install Motor HousingInstall Decals Install Hose ClampsConnect Hoses to Tractor Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch AssemblyWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListRubber Flap SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart Abbreviations Bolt Size ChartIndex AssemblyWarranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company