Woods Equipment S27CD, S22CD, S20CD, S15CD, S25CD manual Install Motor Housing, Assembly Hoses

Page 43

Install Motor Housing

1.Slide motor assembly between shredder center channel and secure to the left side using two 1/2 NC x 1-1/4 carriage bolts (29) and flange lock nuts

(30).

2.Install 1/2 NC x 1 cap screw (31) and flat washer

(32)to the right rear hole of the motor housing and secure with flange lock nuts (30).

3.Install 1/2 NC x 1-1/4 carriage bolt (29) and flange lock nut (30) into the right front hole.

4.Raise motor housing to the bottom of the mounting slots and torque hardware to 85 lbs-ft.

31

30

29

DP1

Figure 54. Motor Assembly Installed

Assembly Hoses

1.Attach male quick coupler (17) and adapter (16) to the end of hose (15). Attach tee (12) to the opposite end of hose.

2.Attach male quick coupler (17) and adapter (16) to the end of second hose (15). Attach check valve (14), nipple (13) and tee (12) to the opposite end of hose.

NOTE: Make sure flow indicator arrow on the side of the check valve (14) is pointing in the correct direction. See Figure 55

3.Install check valve (14) and two nipples (13) between the two tees (12).

NOTE: Make sure flow indicator arrow on the side of the check valve (14) is pointing in the correct direction.

4.Place hose assembly around center plate of shredder and drape quick couplers over the front of the shredder. See Figure 55 and Figure 56.

5.Make sure hose with check valve is on the right side of the center plate.

Figure 55. Hose Assembly

6.Route hose (11) from the IN side of the motor between shredder and rockshaft and attach it to tee (12) on the left side of the center plate.

7.Route hose (11) from the OUT side of the motor between shredder and rockshaft and attach it to tee (12) on the right side of the center plate.

	RETURN
PRESSURE		Center Plate
PRESSURE
		Check
		Valve
11
		ht
		Rig
ft
Le
	IN	11
	IN	OUT
		OUT
		DP2

Figure 56. Hose Routing

MAN0506 (Rev. 9/5/2008)	Assembly 43

Image 43

Contents Flail Shredder Introduction LEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementPreparation Safety RulesTraining Transportation OperationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordAfter operating for 1/2 hour OperationPrincipal Components BREAK-IN of the Flail ShredderChoosing the Correct Tractor HorsepowerTractor Weight PRE-OPERATION Check ListPTO Driveline Length With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Attach Hydraulics Center Cutter Option Without Quick Hitch AttachmentPull-Type Model Attach PTO DrivelineFlail Height Raise StandsRemoving Shredder from Tractor Preparing for OperationPoint & 2-Point Hitch Models SET Operating HeightPoint Hitch Models Pull-Type ModelsStopping the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Starting the TractorTurning CleaningHazard Area Ground SpeedAdditional Rear Wheels Rubber FlapsBED Cones Lubrication Schedule Service & MaintenanceLubricants GreasingLubrication Points Annually Daily or every 8 hours of operationEvery 25 hours of operation Every 40 hours of operationHours Lubrication Service Record Hours Serviced byGearbox OIL Leakage Hours or dailyChanging Gearbox OIL Gearbox leakage & TroubleshootingWheel Spacing Ratchet Height AdjustmentReplacing Flail Knives Servicing Rotors Flail Tubes Replacing Rubber Shield FlapsReplacing Components Removing ComponentsRemoving the Driveline Replacing Stub ShaftServicing Weasler Modular Friction Clutch Breaking In the Clutch RunRebuilding Overrunning Clutch Rebuilding Friction PackMounting Clutch to Shredder Service & Maintenance Problem Cause Solution TroubleshootingWorksheet for Contour Flail Patterns 24’ For Some Models Shipped on End AssemblyWheel Assembly Dealer SET-UP InstructionsALL Units PULL-TYPE Hitch InstallationPull-type units only Safety Light KIT Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Rubber Flap InstallationSafety Light Kit Diagram Non-End Tow Install Center DeflectorBlock Shredded Center CUT KIT InstallationAssemble Motor and Blade Assembly Hoses Install Motor HousingRemove Deflector Kit Install Hose ClampsInstall Decals Connect Hoses to TractorPRE-DELIVERY Check List Dealer Check ListsDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch AssemblyWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListRubber Flap SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart Abbreviations Bolt Size ChartIndex AssemblyWarranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company