Woods Equipment S27CD, S22CD, S20CD, S15CD, S25CD manual Center Drive Gearbox

Page 58

			CENTER DRIVE GEARBOX
REF	PART	QTY	DESCRIPTION
A	1013049	1	Complete gearbox, Series 800
1	1019782	1	Casting, Threaded holes
2	1019783	1	Casting, Non-threaded holes
3	1019784	1	Pinion shaft/gear asy 27T with bearing
			cones & bearing cups
4	90315546	1	Cross shaft/gear asy 20T
5	90101150	1	Bearing cone
6	90101152	2	Bearing cup
7	1019785	4	Bolt, 3/8-16 x 2.75 SHCS
8	1019787	3	Guard, seal
9	90039030	1	Snap ring 1.750
10	90109125	3	Seal TC-1.750-2.437-.312
11	90503078	2	Plug, 1/2-14 NPT SCHD W/3M
12	90003033	8	Bolt, 3/8-16 x 2.25 SHCS
13	90501159	1	Bushing, 1/2 NPT to 1/8 NPT
14	90101328	1	Bearing cone
15	NSS	-	Bearing cone (included in item 3)
16	NSS	-	Bearing cone (included in item 3)
	NSS		Not Serviced Separately

58 Parts	MAN0506 (Rev. 9/5/2008)

Image 58

Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation Safety RulesTraining Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordBREAK-IN of the Flail Shredder OperationPrincipal Components After operating for 1/2 hourPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorPTO Driveline Length With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Attach PTO Driveline Without Quick Hitch AttachmentPull-Type Model Attach Hydraulics Center Cutter OptionPreparing for Operation Raise StandsRemoving Shredder from Tractor Flail HeightPull-Type Models SET Operating HeightPoint Hitch Models Point & 2-Point Hitch ModelsStarting the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Stopping the TractorGround Speed CleaningHazard Area TurningAdditional Rear Wheels Rubber FlapsBED Cones Greasing Service & MaintenanceLubricants Lubrication ScheduleLubrication Points Every 40 hours of operation Daily or every 8 hours of operationEvery 25 hours of operation AnnuallyHours or daily Lubrication Service Record Hours Serviced byGearbox OIL Leakage HoursGearbox leakage & Troubleshooting Changing Gearbox OILWheel Spacing Ratchet Height AdjustmentReplacing Flail Knives Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsBreaking In the Clutch Run Replacing Stub ShaftServicing Weasler Modular Friction Clutch Removing the DrivelineRebuilding Overrunning Clutch Rebuilding Friction PackMounting Clutch to Shredder Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Dealer SET-UP Instructions AssemblyWheel Assembly For Some Models Shipped on EndALL Units PULL-TYPE Hitch InstallationPull-type units only Rubber Flap Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowBlock Shredded Center CUT KIT InstallationAssemble Motor and Blade Install Motor Housing Assembly HosesConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois