Woods Equipment S15CD manual Center CUT KIT Installation, Block Shredded, Assemble Motor and Blade

Page 42

CENTER CUT KIT INSTALLATION

Block Shredded

„Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

To minimize the potential hazards of working under- neath the cutter, follow these procedures.

1.Jackstands with a load rating of 2000 lbs or more are the only approved blocking device for this cutter. Install a minimum of four jackstands under the shredder before working underneath unit.

Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause shredder to fall.

2.Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety.

The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure shredder is approximately level.

3.With full shredder weight lowered onto jackstands, test blocking stability before working underneath.

4.If shredder is attached to tractor when blocking, set the brakes, remove key, and block shredder before working underneath.

5.Securely block rear tractor wheels, in front and behind. Tighten tractor lower 3-point arm anti-sway mechanism to prevent side-to-side movement.

Assemble Motor and Blade

1.Install elbow (8), adapter (9), elbow (10) and hose

(11)to the IN or PRESSURE side of the hydraulic motor.

2.Install adapter (23) and hose (11) to the OUT or RETURN side of the motor.

3.Place motor (4) inside motor housing (2) and secure using six 9/16 NC x 1-1/2 cap screws (7) lock nuts (6).

Make sure OUT or RETRUN side of motor is on the open side of the motor housing. Torque hardware to 171 lbs-ft.

4.Slide blade hub (1) over motor shaft, install 1/4" key and secure using one 5/16 NF x 1-1/2 cap screw (20), flat washers (33) and lock washer (34) in the bottom of the shaft. Torque to 19 lbs-ft.

5.Clamp hub to shaft using two 3/8 NC x 1-3/4 cap screws (18) and lock nuts (22). Torque to 35 lbs-ft.

6.Secure blade (3) to blade hub using two 3/8 NC x 1-1/4 cap screws (19) and flange lock nuts (22). Torque to 35 lbs-ft.

Figure 53. Motor Assembly

42 Assembly

MAN0506 (Rev. 9/5/2008)

 

 

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationSafety Rules PreparationTraining Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordBREAK-IN of the Flail Shredder OperationPrincipal Components After operating for 1/2 hourPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorPTO Driveline Length Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Attach PTO Driveline Without Quick Hitch AttachmentPull-Type Model Attach Hydraulics Center Cutter OptionPreparing for Operation Raise StandsRemoving Shredder from Tractor Flail HeightPull-Type Models SET Operating HeightPoint Hitch Models Point & 2-Point Hitch ModelsStarting the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Stopping the TractorGround Speed CleaningHazard Area TurningRubber Flaps Additional Rear WheelsBED Cones Greasing Service & MaintenanceLubricants Lubrication ScheduleLubrication Points Every 40 hours of operation Daily or every 8 hours of operationEvery 25 hours of operation AnnuallyHours or daily Lubrication Service Record Hours Serviced byGearbox OIL Leakage HoursGearbox leakage & Troubleshooting Changing Gearbox OILRatchet Height Adjustment Wheel SpacingReplacing Flail Knives Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsBreaking In the Clutch Run Replacing Stub ShaftServicing Weasler Modular Friction Clutch Removing the DrivelineRebuilding Friction Pack Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Dealer SET-UP Instructions AssemblyWheel Assembly For Some Models Shipped on EndPULL-TYPE Hitch Installation ALL UnitsPull-type units only Rubber Flap Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowCenter CUT KIT Installation Block ShreddedAssemble Motor and Blade Install Motor Housing Assembly HosesConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitDealer Check Lists PRE-DELIVERY Check ListDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap Bolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois
Top Page Image Contents