Woods Equipment S20CD Daily or every 8 hours of operation, Every 25 hours of operation, Annually

Page 26

Daily or every 8 hours of operation

1.Lubricate PTO U-joints and over-running clutch.

2.Check gearbox daily or every 8 hours of operation. See Figure 24 for gearbox oil fill location.

7109

Figure 24. Gearbox Oil Fill Location

Every 25 hours of operation

1.Lubricate PTO driveline telescoping section (one location, Position B, Figure 23).

2.Lubricate rotor end bearings. See Figure 25.

3.Lubricate wheel rockshaft bearings (3 to 5 locations). See Figure 26.

7123Z

Figure 25. Rotor End Bearing

Lubrication Point

7114Z

Figure 26. Wheel Rockshaft Bearing

Lubrication Points

Every 40 hours of operation

1.Lubricate rotor drive couplers next to the couplers on underside of unit and inside of flail tube (use hole in flail tube to access grease fitting, 2 locations).

2.Grease the drive hubs with 10 to 20 pumps. You may use extra grease only on drive hubs.

Annually

1.Change gearbox oil. Refill with SAE 85W90 gear oil. Capacity: 2-1/2 U.S. quarts (110 oz.). See Figure 27.

ROTOR

DRIVE HUB

GEARBOX

OIL DRAIN

Figure 27. Gearbox Oil Drain Location

2.Repack wheel bearings. See Figure 28.

7126Z

Figure 28. Wheel Bearings

3.Lubricate ratchets as necessary (2 locations each ratchet). See Figure 29.

7104Z

Figure 29. Ratchet Lubrication Points

26 Service & Maintenance

(Rev. 1/24/2011) MAN0506 (Rev. 9/5/2008)

Image 26

Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationTraining Safety RulesPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordBREAK-IN of the Flail Shredder OperationPrincipal Components After operating for 1/2 hourPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorPTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Attach PTO Driveline Without Quick Hitch AttachmentPull-Type Model Attach Hydraulics Center Cutter OptionPreparing for Operation Raise StandsRemoving Shredder from Tractor Flail HeightPull-Type Models SET Operating HeightPoint Hitch Models Point & 2-Point Hitch ModelsStarting the Tractor Setting Flail HeightSetting Outer Trailing Wheels Casters & Struts Stopping the TractorGround Speed CleaningHazard Area TurningBED Cones Rubber FlapsAdditional Rear Wheels Greasing Service & MaintenanceLubricants Lubrication ScheduleLubrication Points Every 40 hours of operation Daily or every 8 hours of operationEvery 25 hours of operation AnnuallyHours or daily Lubrication Service Record Hours Serviced byGearbox OIL Leakage HoursGearbox leakage & Troubleshooting Changing Gearbox OILReplacing Flail Knives Ratchet Height AdjustmentWheel Spacing Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsBreaking In the Clutch Run Replacing Stub ShaftServicing Weasler Modular Friction Clutch Removing the DrivelineMounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Dealer SET-UP Instructions AssemblyWheel Assembly For Some Models Shipped on EndPull-type units only PULL-TYPE Hitch InstallationALL Units Rubber Flap Installation Manual Storage Tube InstallationOptional Equipment Rubber Belting Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowAssemble Motor and Blade Center CUT KIT InstallationBlock Shredded Install Motor Housing Assembly HosesConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois