Woods Equipment S27CD, S22CD, S20CD, S15CD, S25CD manual Woods Equipment Company

Page 68

Woods Equipment Company

2606 South Illinois Route 2

Post Office Box 1000

Oregon, Illinois 61061

800-319-6637 tel

800-399-6637 fax www.WoodsEquipment.com

©2006 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.

Image 68

Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationTraining Safety RulesPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation Principal ComponentsBREAK-IN of the Flail Shredder After operating for 1/2 hourHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Without Quick Hitch Attachment Pull-Type ModelAttach PTO Driveline Attach Hydraulics Center Cutter OptionRaise Stands Removing Shredder from TractorPreparing for Operation Flail HeightSET Operating Height Point Hitch ModelsPull-Type Models Point & 2-Point Hitch ModelsSetting Flail Height Setting Outer Trailing Wheels Casters & StrutsStarting the Tractor Stopping the TractorCleaning Hazard AreaGround Speed TurningBED Cones Rubber FlapsAdditional Rear Wheels Service & Maintenance LubricantsGreasing Lubrication ScheduleLubrication Points Daily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation AnnuallyLubrication Service Record Hours Serviced by Gearbox OIL LeakageHours or daily HoursGearbox leakage & Troubleshooting Changing Gearbox OILReplacing Flail Knives Ratchet Height AdjustmentWheel Spacing Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsReplacing Stub Shaft Servicing Weasler Modular Friction ClutchBreaking In the Clutch Run Removing the DrivelineMounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Assembly Wheel AssemblyDealer SET-UP Instructions For Some Models Shipped on EndPull-type units only PULL-TYPE Hitch InstallationALL Units Manual Storage Tube Installation Optional Equipment Rubber Belting InstallationRubber Flap Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowAssemble Motor and Blade Center CUT KIT InstallationBlock Shredded Install Motor Housing Assembly HosesInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois