Woods Equipment S15CD, S22CD manual Replacing Stub Shaft, Servicing Weasler Modular Friction Clutch

Page 32

REPLACING STUB SHAFT

1. Remove rotor (see Servicing Rotors (Flail Tubes), page 30).

2. Remove three 1/2 x 2-1/2 hex bolts in taper lock hub and re-install bolts in three threaded holes (see Figure 38).

3. Tighten bolts evenly to release taper lock hub from stub shaft. NOTE: You may have to give a sharp blow directly to each bolt head to help the hub disengage.

4. Unscrew stub shaft from the rotor tube.

Figure 37. Rotor Direction of Rotation

5. Install new stub shaft, reversing Steps 1-3.

Figure 38. Stub Shaft Assembly

SERVICING WEASLER MODULAR FRICTION CLUTCH

Tools Required

•3/4" Socket wrench

•8" Minimum C-clamps (2)

•1/4" Hex Allen wrench

•Regular screwdriver or punch

•Duct tape or locking pliers with 3" throat minimum

•Hammer

•1/2" sq. to 1" sq. bar x 9"

•Scale or Vernier

Breaking In the Clutch (Run In)

NOTE: All new clutches must be broken in (Run in) and any clutch that has not been used for approximately 60 days.

1.Shut off tractor and disengage PTO.

2.Disconnect driveline from the tractor PTO shaft.

3.Loosen the bolts on the outside diameter of the clutch until all bolts are just loose, then tighten all bolts 1/2 turn.

4.Attach the driveline to the tractor PTO. Stand clear of the unit.

5.Start tractor. Engage PTO clutch and run for a few seconds or until clutch visibly smokes.

6.Disengage PTO. Shut off tractor. Disconnect driveline from the tractor.

7.Tighten all bolts on the outside diameter of the clutch until the compression plate is tight against the housing.

8.Grease the fitting on the yoke, using a multi- purpose high-temperature EP grease or an equivalent lithium grease.

9.For an integral overrunning clutch, make sure clutch turns freely in one direction.

Removing the Driveline

1.Shut off tractor and disengage PTO.

2.Disconnect driveline from PTO shaft.

3.Remove the bolt (21K) or clamp (24K) that attaches the clutch to the shredder’s input shaft.

32 Service & Maintenance	MAN0506 (Rev. 9/5/2008)

Image 32

Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationTraining Safety RulesPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation Principal ComponentsBREAK-IN of the Flail Shredder After operating for 1/2 hourHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Without Quick Hitch Attachment Pull-Type ModelAttach PTO Driveline Attach Hydraulics Center Cutter OptionRaise Stands Removing Shredder from TractorPreparing for Operation Flail HeightSET Operating Height Point Hitch ModelsPull-Type Models Point & 2-Point Hitch ModelsSetting Flail Height Setting Outer Trailing Wheels Casters & StrutsStarting the Tractor Stopping the TractorCleaning Hazard AreaGround Speed TurningBED Cones Rubber FlapsAdditional Rear Wheels Service & Maintenance LubricantsGreasing Lubrication ScheduleLubrication Points Daily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation AnnuallyLubrication Service Record Hours Serviced by Gearbox OIL LeakageHours or daily HoursGearbox leakage & Troubleshooting Changing Gearbox OILReplacing Flail Knives Ratchet Height AdjustmentWheel Spacing Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsReplacing Stub Shaft Servicing Weasler Modular Friction ClutchBreaking In the Clutch Run Removing the DrivelineMounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Assembly Wheel AssemblyDealer SET-UP Instructions For Some Models Shipped on EndPull-type units only PULL-TYPE Hitch InstallationALL Units Manual Storage Tube Installation Optional Equipment Rubber Belting InstallationRubber Flap Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowAssemble Motor and Blade Center CUT KIT InstallationBlock Shredded Install Motor Housing Assembly HosesInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois