Woods Equipment S22CD, S20CD, S15CD, S27CD, S25CD manual Index, Assembly

Page 65

INDEX

ASSEMBLY

Dealer Set-Up Instructions 38

Optional Equipment

Center Cut Kit Installation 42

Rubber Belting Installation 40

Rubber Flap Installation 40

Safety Light Kit Installation 40

DEALER CHECK LISTS

Delivery Check List (Dealer’s Responsibility) 45

Pre-Delivery Check List

(Dealer’s Responsibility) 45

GENERAL

Abbreviations 62

Balance Statement 5

Bolt Size Chart 62

Bolt Torque Chart 61

Flail Pattern Worksheets 36

General Information 5

Introduction 2

Obtaining Replacement Manuals 2

Specifications 4

Table of Contents 3

Warranty

Product 65

Replacement Parts 1

Worksheets for Contour Flail Patterns 36

OPERATION

Attaching Shredder to Tractor 17

Hydraulics (Center Cutter Option) 18

PTO Driveline 18

Pull-Type Model 18

Raising Stands 19

With Quick Hitch 17

Without Quick Hitch 18

Break-In Period 14

Choosing the Correct Tractor 15

Cleaning 22

Field Operation 19

Flail Knives 20

Ground Speed 22

Hazard Area 22

Setting Flail Height 21

Setting Operating Height 20

Setting Outer Trailing Wheels 21

Starting the Tractor 21

Stopping the Tractor 21

Turning 22

OPERATION (CONTINUED)

Optional Equipment

Additional Rear Wheels 23

Bed Cones for 3-Point Units 23

Rubber Flaps 23

Pre-Operation Check List

(Owner’s Responsibility) 15

Preparing for Operation 19

Principal Components 14

PTO Driveline Length (3-Point & 2-Point Models) 16 Removing Shredder from Tractor 19

Storage 23

Tractor horsepower vs. unit width (Table 1) 16

SAFETY

Check Lists

Delivery (Dealer’s Responsibility) 45

Pre-Delivery (Dealer’s Responsibility) 45

Pre-Operation (Owner’s Responsibility) 15

Hazard Area 22

Operator Sign-Off Record 13

Safety Decals 10, 11, 12

Safety Rules 6, 7, 8, 9

Safety Symbols Explained 2

SERVICE & MAINTENANCE

Balance Statement 5

Changing Gearbox Oil 28

Gearbox Oil Leakage 27

Greasing 24

Lubricants 24

Lubrication Points Diagram 25

Lubrication Schedule 24

Lubrication Service Record 27

Mounting Clutch to Shredder 33

Ratchet Height Adjustment 29

Replacing Flail Knives 29

Replacing Rubber Shield Flaps 30

Replacing Stub Shaft 32

Servicing Rotors 30

Removing Components 31

Replacing Components 31

Servicing Weasler Modular Friction Clutch 32 Wheel Spacing 29

TROUBLESHOOTING 35

MAN0506 (Rev. 9/5/2008)	Index 65

Image 65

Contents Flail Shredder Introduction LEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementTraining Safety RulesPreparation Transportation OperationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordPrincipal Components OperationBREAK-IN of the Flail Shredder After operating for 1/2 hourTractor Weight HorsepowerPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Pull-Type Model Without Quick Hitch AttachmentAttach PTO Driveline Attach Hydraulics Center Cutter OptionRemoving Shredder from Tractor Raise StandsPreparing for Operation Flail HeightPoint Hitch Models SET Operating HeightPull-Type Models Point & 2-Point Hitch ModelsSetting Outer Trailing Wheels Casters & Struts Setting Flail HeightStarting the Tractor Stopping the TractorHazard Area CleaningGround Speed TurningBED Cones Rubber FlapsAdditional Rear Wheels Lubricants Service & MaintenanceGreasing Lubrication ScheduleLubrication Points Every 25 hours of operation Daily or every 8 hours of operationEvery 40 hours of operation AnnuallyGearbox OIL Leakage Lubrication Service Record Hours Serviced byHours or daily HoursChanging Gearbox OIL Gearbox leakage & TroubleshootingReplacing Flail Knives Ratchet Height AdjustmentWheel Spacing Servicing Rotors Flail Tubes Replacing Rubber Shield FlapsReplacing Components Removing ComponentsServicing Weasler Modular Friction Clutch Replacing Stub ShaftBreaking In the Clutch Run Removing the DrivelineMounting Clutch to Shredder Rebuilding Friction PackRebuilding Overrunning Clutch Service & Maintenance Problem Cause Solution TroubleshootingWorksheet for Contour Flail Patterns 24’ Wheel Assembly AssemblyDealer SET-UP Instructions For Some Models Shipped on EndPull-type units only PULL-TYPE Hitch InstallationALL Units Optional Equipment Rubber Belting Installation Manual Storage Tube InstallationRubber Flap Installation Safety Light KIT InstallationSafety Light Kit Diagram Non-End Tow Install Center DeflectorAssemble Motor and Blade Center CUT KIT InstallationBlock Shredded Assembly Hoses Install Motor HousingInstall Decals Install Hose ClampsConnect Hoses to Tractor Remove Deflector KitDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler Automatic Clutch Optional Weasler 24K Torqmaster Clutch AssemblyWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Center Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListRubber Flap Metric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Abbreviations Bolt Size ChartIndex AssemblyWarranty Rev /3/2011 South Illinois Route Post Office Box Oregon, Illinois Woods Equipment Company