Woods Equipment S22CD, S20CD Manual Storage Tube Installation, For One-Piece Style Manual Tube

Page 40

MANUAL STORAGE TUBE INSTALLATION

The manual storage tube may be supplied in either of the following styles.

For One-Piece Style Manual Tube:

Mount the manual tube to the inside of the shredder side sheet, using three 3/8 x 1-1/4" hex bolts, washers, and 3/8" nuts. Mounting holes are located above the bearing plate (see Figure 46).

Figure 46. One-Piece Style Manual Tube Installed

For Clamp-Style Manual Tube:

1.Mount the tube clamp to the inside of the shredder side sheet using two 1/4" self-tapping screws (Figure 47). Mounting holes are located above the bearing plate.

2.Place the tube in the clamp with the cap facing forward.

NOTE: Keep the Operator’s Manual with the shredder at all times.

Figure 47. Clamp-Style Manual Tube Assembly

OPTIONAL EQUIPMENT

RUBBER BELTING INSTALLATION

1.Remove all components from shipping carton. Make sure that all required hardware is included.

2.Attach rubber belting and bars to front of shredder using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange lock nuts.

NOTE: Use equal number of belting and bars on each side of shredder.

3.Tighten all hardware.

RUBBER FLAP INSTALLATION

1.Remove all components from shipping carton. Make sure that all required hardware is included.

2.Attach flap brackets to the front of the shredder using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange lock nuts.

NOTE: Use flap brackets to space flap brackets out evenly across front of shredder.

3.Attach flap bars to flat brackets using 3/8 NC x 1- 1/2 carriage bolts and 3/8 flange lock nuts.

4.Assemble rod and rubber flaps through flap brackets and secure using 3/16 x 1-1/2 cotter pins.

5.Tighten all hardware.

6.For detailed installation instructions, see the parts diagram and instruction sheet the comes with the swing flap kit designed for each shredder.

1.Rubber flap

2.Flap bracket, right

3.Flap bracket, left

5.flap rod

6.Swing flap bar, mast plate

7.Swing flap bar

8.3/8 NC x 1 Carriage bolt

9.3/8 NC Flange lock nut

10. 3/16 x 1-1/2 Cotter pin

Figure 48. Rubber Flat Installation (15’ Shown)

SAFETY LIGHT KIT INSTALLATION

1.Remove all components from shipping carton. Make sure that all required hardware is included.

2.Attach dual safety lights (Figure 49) to their bases using 1/4 NC x 1" hex bolts, washers and nuts

40 Assembly	MAN0506 (Rev. 9/5/2008)

Image 40

Contents Flail Shredder Introduction Table of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation Safety RulesTraining Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation Principal ComponentsBREAK-IN of the Flail Shredder After operating for 1/2 hourHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Without Quick Hitch Attachment Pull-Type ModelAttach PTO Driveline Attach Hydraulics Center Cutter OptionRaise Stands Removing Shredder from TractorPreparing for Operation Flail HeightSET Operating Height Point Hitch ModelsPull-Type Models Point & 2-Point Hitch ModelsSetting Flail Height Setting Outer Trailing Wheels Casters & StrutsStarting the Tractor Stopping the TractorCleaning Hazard AreaGround Speed TurningAdditional Rear Wheels Rubber FlapsBED Cones Service & Maintenance LubricantsGreasing Lubrication ScheduleLubrication Points Daily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation AnnuallyLubrication Service Record Hours Serviced by Gearbox OIL LeakageHours or daily HoursGearbox leakage & Troubleshooting Changing Gearbox OILWheel Spacing Ratchet Height AdjustmentReplacing Flail Knives Replacing Rubber Shield Flaps Servicing Rotors Flail TubesRemoving Components Replacing ComponentsReplacing Stub Shaft Servicing Weasler Modular Friction ClutchBreaking In the Clutch Run Removing the DrivelineRebuilding Overrunning Clutch Rebuilding Friction PackMounting Clutch to Shredder Service & Maintenance Troubleshooting Problem Cause SolutionWorksheet for Contour Flail Patterns 24’ Assembly Wheel AssemblyDealer SET-UP Instructions For Some Models Shipped on EndALL Units PULL-TYPE Hitch InstallationPull-type units only Manual Storage Tube Installation Optional Equipment Rubber Belting InstallationRubber Flap Installation Safety Light KIT InstallationInstall Center Deflector Safety Light Kit Diagram Non-End TowBlock Shredded Center CUT KIT InstallationAssemble Motor and Blade Install Motor Housing Assembly HosesInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDelivery Check List Dealer Check Lists Parts Index Flail Shredder Center Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightTing BED Cone Assembly Optional Parts Dual Safety Light KIT Optional Weasler 24K Torqmaster Clutch Assembly Weasler Automatic Clutch OptionalWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Optional 1019820 Center Drive Gearbox Rubber Belting Advertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalRubber Flap SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Rev /3/2011 Woods Equipment Company South Illinois Route Post Office Box Oregon, Illinois