MTD PS manual Assembly of Pole SAW, Adjusting Pole Length

Page 12

ASSEMBLY INSTRUCTIONS

ABC

Fig.4

D

Fig.5

3.After adjustment and while wearing heavy duty work gloves, move the saw chain back and forth on the guide bar to be sure the chain moves freely and is in proper mesh with sprocket. Do not move chain with bare hands.

NOTE: IF the chain is difficult to rotate or if it binds on the guide bar, too much tension has been applied and must be adjusted. To decrease tension, turn the adjustment screw counterclockwise slowly. Move the chain back and forth until it moves freely.

4.Holding the nose in upper position, securely tighten the bar retaining nuts (70 inch lbs.)

ASSEMBLY OF POLE SAW

1.Make sure the unit is unplugged from power source.

2.Slip handle bracket (A) over chain saw handle from the right side (See Fig. 7).

NOTE: The trigger must be depressed before the bracket will go onto the handle. Push the lock-off button and depress the trigger. While holding the trigger in, place the trigger support portion of the bracket under the trig- ger and slide the bracket onto the chain saw handle. The bracket will keep the trigger in the “ON” position.

A

B

E

Fig.6

2.Holding the nose of the bar up, use the screwdriver or scrench if provided in your User’s Kit to turn the guide bar adjustment screw (E) (Fig. 6) clockwise to tighten the chain. Turning the screw COUNTERCLOCKWISE LOOSENS THE CHAIN on the guide bar.

Fig.7

3.Align holes in pole bracket with holes in handle bracket. Install Phillips head screws with lock washers through pole bracket from left side and thread into the weld nuts on the handle bracket. Tighten screws securely.

4.Plug the saw power cord into receptacle cord at end of inner pole.

ADJUSTING POLE LENGTH

The pole saw has a telescoping pole assembly that will extend from 57 inches (fully retracted) to 96 inches (fully extended). A threaded compression coupling is used to hold the pole in position at any extended length.

11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Table of Contents Warranty StatementSymbol Meaning Rules for Safe OperationKickback Safety Precautions Safety and International Symbols Chain Components Kickback Specifics Important Safety Instructions Read ALL InstructionsPage Pole SAW Trimming Precautions Save These InstructionsAssembly Instructions Assembly of Pole SAW Adjusting Pole LengthOiling Chain Cutting with the Pole SAWFilling OIL Tank Selecting the Proper Extension Cord for Your SAW ModelOperating Instructions Cutting with only the Chain SAWTo Stop Motor No Serviceable Parts Inside Chain and BAR LubricationExtension Cords Double InsulationGeneral Cutting Instructions Trimming a Tree PruningFelling Felling a TreeGeneral Guidelines for Felling Trees Felling CUTBucking Using a Sawhorse LimbingBucking Vertical CuttingMaintenance Instructions Guide BAR MaintenanceChain Maintenance Instructions Preventative Maintenance Chain TensionBreaking in a NEW SAW Chain Servicing a Double Insulated ApplianceParts List Parts No DescriptionMTD LLC Manuel de L’utilisateur Table DES Matières Declaration DE GarantieAlerte DE Sécurité Règles DE SécuritéAvertissement Les rebonds Symboles DE Sécurité ET Internationaux Dispositifs DE Securite Avertissement Lesrebonds Instructions DE Surete Importantes Lire Toutes LES InstructionsNutiliser Aucun Autre Accesoire OU Conserver CES Instructions Instructions D’ASSEMBLEE DeballageMontage D’ELEMENTS Reglage DE LA Tension DE LA ChaineMontage DE LA Perche Elagueuse Reglage DE LA Longueur DE LA CanneLubrefacation DE LA Chaine Coupe a L’AIDE DE LA Perche ElagueuseRemplissage DU Reservoir a Huile Choix D’UN Prolongateur Electrique ApproprieConsignes D’UTILISATION Demarrage DE LA Perche ElagueuseArret DU Moteur Lubrification DE LA Chaine ET DU DUIDE-CHAINE Prolongateurs ElectriquesAucune Piece Interne Reparable Instructions DE Decoupage Generales Ailler UN Arbre ElaguarAbattage Abattage D’UN ArbreRegles Generales a Observer Pour L’ABATTAGE Trait D’ABATTAGEEbranchage Tronconnage SUR ChevaletTronconnage Coupe VerticaleInstructions D’ENTRETIEN Entretien DU GUIDE-CHAINEEntretien DE LA Chaine Tension DE LA Chaine Rodage D’UNE Nouvelle Chaine DE TronconneuseEntretien Preventif Reparation D’UN Appareil a Double ISOLA- TionListe DES Pièces RОfОrenceGarantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Índice Declaración DE GarantíaAlerta DE Seguridad Normas DE SeguridadAdvertencia El con Simbolos DE Seguridad E Internacionales Aspectos DE Seguridad Advertencia Instrucciones DE Seguridad Importantes LEA Todas LAS LAS InstruccionesPage Guarde Estas Instrucciones Precauciones DE Corte CON LA SIER- RA TelescopicaInstrucciones DE Asamblea Adjustando LA Longitude DE EL Tubo Ensamble DE LA Motosierra TELE- ScopicaAceitar LA Cadena Cortando CON LA Motosierra Tele ScopicaLlenando EL Tanque DE Aceite Seleccionando EL Cable DE Extension CorrectoInstrucciones DE Funcionamientto Para Arrancar LA SierraPara Apagar EL Motor Lubricacion DE Barra Y Cadena Cables DE ExtensionAislacion Doble Instrucciones DE Corte Generales Podando UN ArbolTalado Desramando UN ArbolReglas Generales Para EL Talado DE Arboles Corte DE TaladoDesramado LeñadoLeñado Usando UN Caballete Para Aserrar Cortando VerticalmenteInstrucciones DEL Mantenimiento Mantenimiento DE LA Barra GuiaInstrucciones DE Mantenimiento DE LA Cadena Tension DE LA Sierra Acondicionamiento EN UNA Cadena Para Sierra NuevaMantenimiento Preventivo Servicio AL Aparato DE Aislado DobleLista DE Piezas Nota MTD LLC Stop

PS specifications

MTD PS, or Machine Translation Deep Post-Editing System, is an innovative solution designed to improve the accuracy and quality of machine-generated translations. This system is particularly instrumental for businesses and organizations that rely on multilingual communication and require high-quality translations for documents, websites, and other materials.

One of the main features of MTD PS is its deep learning architecture, which employs neural networks to analyze and refine machine-generated translations. This technology allows the system to understand linguistic nuances, context, and semantics, resulting in translations that are not only grammatically correct but also culturally relevant. The adaptability of deep learning means that the system can continuously improve over time by learning from user feedback and various language data.

Another significant characteristic of MTD PS is its user-friendly interface. Designed with usability in mind, the system allows post-editors to review and enhance translations with ease. Suggestions for improvements are generated in real-time, enabling human translators to make quick decisions and apply necessary changes. This collaboration between humans and machines amplifies productivity while maintaining high standards of quality.

MTD PS integrates advanced natural language processing (NLP) technologies, which are crucial for understanding and generating human-like text. With features such as context-aware formatting and terminology management, the system ensures consistency across different translations, streamlining the localization process. NLP capabilities also facilitate the handling of idiomatic expressions and jargon specific to certain fields, enabling the system to cater to various industries.

Additionally, MTD PS is equipped with extensive data analytics features. It allows users to track performance metrics such as translation accuracy and editor efficiency. This data-driven approach helps organizations evaluate the effectiveness of their translation processes and make informed decisions about future localization strategies.

In summary, MTD PS is a powerful tool that leverages deep learning, NLP technologies, and user-centric design to enhance the quality of machine translations. Its ability to adapt, learn, and provide actionable insights makes it an invaluable asset for a wide range of applications in the global marketplace. As businesses continue to expand their reach across borders, systems like MTD PS will play a pivotal role in ensuring effective communication and fostering collaboration across cultures.
Top Page Image Contents