MTD PS manual Guide BAR Maintenance, Chain Maintenance Instructions

Page 19

MAINTENANCE INSTRUCTIONS

GUIDE BAR MAINTENANCE

Ensure that the WARNING: power cord is discon- nected before per-

forming any maintenance on your saw.

Fig.26

Proper maintenance of the guide bar, as explained in

this section, is essential to keep your saw in good

working order.

GUIDE BAR MAINTENANCE :

Most guide bar problems can be prevented merely by keeping the chain saw well maintained.

Incorrect filing and non-uniform cutter and depth gauge set- tings cause most guide bar problems, primarily resulting in uneven bar wear. As the bar wears unevenly, the rails widen, which may cause chain clatter and difficulty in mak- ing straight cuts.

Insufficient guide bar lubrication and operating the saw with a chain that is TOO TIGHT will contribute to rapid bar wear

.

To help minimize bar wear, the following guide bar mainte- nance is recommended.

BAR WEAR - Turn guide bar frequently at regular intervals (for example, after 5 hours of use), to ensure even wear on top and bottom of bar.

BAR GROOVES - Bar grooves (or rails which support and carry the chain) should be cleaned if the saw has been heavily used or if the saw chain appears dirty. Rails should always be cleaned every time the saw chain is removed.

OIL PASSAGES - Oil passages at bar pad should be cleaned to ensure proper lubrication of the bar and chain during operation. This can be done using a soft wire small enough to insert into the oil discharge hole.

To Clean Guide Bar Rails:

1.Remove sprocket cover, bar and chain .

2.Using a screwdriver, putty knife, wire brush or other sim- ilar instrument, clear residue from the rails on the guide bar.

This will keep the oil passages open to provide proper lubrication to the bar and chain (Figure 26).

3.Reinstall the bar, chain and bar bolt retaining nuts. .

CHAIN MAINTENANCE INSTRUCTIONS

Unless you have experi- WARNING: ence and specialized

training for dealing with kickback (see Safety Precautions), always use a low-kickback saw chain, which significantly reduces the danger of kickback. Low-kickback saw chain does not completely eliminate kickback.

A low-kickback or “safety chain”, should never be regarded as total protection against injury.A low-kickback saw chain should always be used in conjunction with other kickback protection devices such as the Hand Guard furnished with your unit.

Always use a replacement saw chain designed as “low- kickback” or a saw chain which meets the low-kickback performance.

A standard saw chain (a chain which does not have the kickback reducing guard links) should only be used by an experienced professional chain saw operator.

What is a Low-Kickback Saw Chain?

A low-kickback saw chain is a chain which has met the kickback performance requirements of ANSI B175.1. Do not use other replacement chain unless it has met these requirements for your specific model.

By keeping the saw chain in good working condition and correctly serviced as recommended in this manual, you will be able to maintain the safety system of your chain saw over the life of the product.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operator’s Manual Warranty Statement Table of ContentsRules for Safe Operation Symbol MeaningKickback Safety Precautions Safety and International Symbols Chain Components Kickback Specifics Read ALL Instructions Important Safety InstructionsPage Save These Instructions Pole SAW Trimming PrecautionsAssembly Instructions Adjusting Pole Length Assembly of Pole SAWSelecting the Proper Extension Cord for Your SAW Model Oiling ChainCutting with the Pole SAW Filling OIL TankCutting with only the Chain SAW Operating InstructionsTo Stop Motor Double Insulation No Serviceable Parts InsideChain and BAR Lubrication Extension CordsFelling a Tree General Cutting InstructionsTrimming a Tree Pruning FellingFelling CUT General Guidelines for Felling TreesVertical Cutting Bucking Using a SawhorseLimbing BuckingGuide BAR Maintenance Maintenance InstructionsChain Maintenance Instructions Servicing a Double Insulated Appliance Preventative MaintenanceChain Tension Breaking in a NEW SAW ChainParts No Description Parts ListMTD LLC Manuel de L’utilisateur Declaration DE Garantie Table DES MatièresRègles DE Sécurité Alerte DE SécuritéAvertissement Les rebonds Symboles DE Sécurité ET Internationaux Dispositifs DE Securite Avertissement Lesrebonds Lire Toutes LES Instructions Instructions DE Surete ImportantesNutiliser Aucun Autre Accesoire OU Conserver CES Instructions Reglage DE LA Tension DE LA Chaine Instructions D’ASSEMBLEEDeballage Montage D’ELEMENTSReglage DE LA Longueur DE LA Canne Montage DE LA Perche ElagueuseChoix D’UN Prolongateur Electrique Approprie Lubrefacation DE LA ChaineCoupe a L’AIDE DE LA Perche Elagueuse Remplissage DU Reservoir a HuileDemarrage DE LA Perche Elagueuse Consignes D’UTILISATIONArret DU Moteur Prolongateurs Electriques Lubrification DE LA Chaine ET DU DUIDE-CHAINEAucune Piece Interne Reparable Abattage D’UN Arbre Instructions DE Decoupage GeneralesAiller UN Arbre Elaguar AbattageTrait D’ABATTAGE Regles Generales a Observer Pour L’ABATTAGECoupe Verticale EbranchageTronconnage SUR Chevalet TronconnageEntretien DU GUIDE-CHAINE Instructions D’ENTRETIENEntretien DE LA Chaine Reparation D’UN Appareil a Double ISOLA- Tion Tension DE LA ChaineRodage D’UNE Nouvelle Chaine DE Tronconneuse Entretien PreventifRОfОrence Liste DES PiècesGarantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Declaración DE Garantía ÍndiceNormas DE Seguridad Alerta DE SeguridadAdvertencia El con Simbolos DE Seguridad E Internacionales Aspectos DE Seguridad Advertencia LEA Todas LAS LAS Instrucciones Instrucciones DE Seguridad ImportantesPage Precauciones DE Corte CON LA SIER- RA Telescopica Guarde Estas InstruccionesInstrucciones DE Asamblea Ensamble DE LA Motosierra TELE- Scopica Adjustando LA Longitude DE EL TuboSeleccionando EL Cable DE Extension Correcto Aceitar LA CadenaCortando CON LA Motosierra Tele Scopica Llenando EL Tanque DE AceitePara Arrancar LA Sierra Instrucciones DE FuncionamienttoPara Apagar EL Motor Cables DE Extension Lubricacion DE Barra Y CadenaAislacion Doble Desramando UN Arbol Instrucciones DE Corte GeneralesPodando UN Arbol TaladoCorte DE Talado Reglas Generales Para EL Talado DE ArbolesCortando Verticalmente DesramadoLeñado Leñado Usando UN Caballete Para AserrarMantenimiento DE LA Barra Guia Instrucciones DEL MantenimientoInstrucciones DE Mantenimiento DE LA Cadena Servicio AL Aparato DE Aislado Doble Tension DE LA SierraAcondicionamiento EN UNA Cadena Para Sierra Nueva Mantenimiento PreventivoLista DE Piezas Nota MTD LLC Stop

PS specifications

MTD PS, or Machine Translation Deep Post-Editing System, is an innovative solution designed to improve the accuracy and quality of machine-generated translations. This system is particularly instrumental for businesses and organizations that rely on multilingual communication and require high-quality translations for documents, websites, and other materials.

One of the main features of MTD PS is its deep learning architecture, which employs neural networks to analyze and refine machine-generated translations. This technology allows the system to understand linguistic nuances, context, and semantics, resulting in translations that are not only grammatically correct but also culturally relevant. The adaptability of deep learning means that the system can continuously improve over time by learning from user feedback and various language data.

Another significant characteristic of MTD PS is its user-friendly interface. Designed with usability in mind, the system allows post-editors to review and enhance translations with ease. Suggestions for improvements are generated in real-time, enabling human translators to make quick decisions and apply necessary changes. This collaboration between humans and machines amplifies productivity while maintaining high standards of quality.

MTD PS integrates advanced natural language processing (NLP) technologies, which are crucial for understanding and generating human-like text. With features such as context-aware formatting and terminology management, the system ensures consistency across different translations, streamlining the localization process. NLP capabilities also facilitate the handling of idiomatic expressions and jargon specific to certain fields, enabling the system to cater to various industries.

Additionally, MTD PS is equipped with extensive data analytics features. It allows users to track performance metrics such as translation accuracy and editor efficiency. This data-driven approach helps organizations evaluate the effectiveness of their translation processes and make informed decisions about future localization strategies.

In summary, MTD PS is a powerful tool that leverages deep learning, NLP technologies, and user-centric design to enhance the quality of machine translations. Its ability to adapt, learn, and provide actionable insights makes it an invaluable asset for a wide range of applications in the global marketplace. As businesses continue to expand their reach across borders, systems like MTD PS will play a pivotal role in ensuring effective communication and fostering collaboration across cultures.
Top Page Image Contents