MTD PS manual Oiling Chain, Cutting with the Pole SAW, Filling OIL Tank

Page 13

ASSEMBLY INSTRUCTIONS

UNLOCKLOCK

DÉVERROUILLEZSERRURE

ABRABLOQUEO

Fig.8

1.To extend the pole, loosen coupling by turning coupling nut counterclockwise as shown in Fig. 8. Pole will slide freely.

2.Pull inner pole section out to desired length of exten- sion. Note: Only extend pole to minimum length required to reach limb that is being cut.

3.To lock pole in position, tighten coupling by turning cou- pling nut clockwise (See Fig. 8) until firmly hand tight. Make sure saw handle is aligned with pole handle before tightening coupling nut.

IMPORTANT: Do not use wrench or pliers to overtight- en coupling. Damage to coupling or pole may result.

OILING CHAIN

To oil chain, press oil cap. Oil will feed onto guide bar and chain. Press oil cap at least once before each cut. Always check oil level before using pole saw. check oil level often by looking at oil sight level hole. Oil sight level hole is on left side of saw, between front handle and front hand guard. Do not attempt to operate the oiler while cutting with the pole saw.

Grip Area

Zone de Poignée Área del Apretón

Fig.9

Lock-Off Switch

Gâchette de Contact

Fijador del Interruptor

Trigger Switch

Interrupteur de Gachette

Interruptor de Gatillo

CUTTING WITH THE POLE SAW

1.Connect saw to extension cord. Connect extension cord to power supply.

2.Use both hands to grip pole saw. Use only designated grip areas when operating pole saw (See Fig. 9). Use firm grip. Thumbs and fingers must wrap around pole saw handle and pole.

3.Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet.

4.When ready to make a cut, press in trigger switch lock- off and squeeze trigger switch (see Fig. 10) This will turn pole saw on. Releasing trigger switch will turn pole saw off. Make sure saw is running at full speed before starting a cut.

5.When starting a cut, place moving chain against wood. Hold pole saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw.

6.Guide pole saw using light pressure. Do not force pole saw. The motor will overload and can burn out. It will do the job better and safer at the rate for which it was intended.

7.Remove pole saw from a cut with saw running at full speed. Stop pole saw by releasing trigger. Make sure chain has stopped before setting pole saw down.

8.Never stand directly under the limb you are trimming. Always position yourself out of the path of falling debris.

FILLING OIL TANK

Using a funnel, fill oil tank with MTD Chain, Bar and Sprocket oil. Wipe up any spills. Make sure no dirt gets into the oil tank.

SELECTING THE PROPER EXTENSION CORD FOR YOUR SAW MODEL

Minimum Gauge Wire

Saw Model

Ampere

Volts AC

Length of Power Cord

 

Rating

 

25 ft. / 7.5m

50 ft. / 15m

100 ft. / 30m

MTD PS

8

110 / 120

18 Gauge

16 Gauge

14 Gauge

 

 

 

 

 

 

Fig.11

1.When using the appliance, an extension cord of ade- quate size must be used for safety and to prevent loss of power and overheating.

2.The extension cord must be specifically intended for out- door use and marked SW-A, SOW-A, STOW-A, SJW-A, SJOW-A SJTOW-A, SJTW-A, OR SJTW.

Fig.10

12

Image 13
Contents Operator’s Manual Warranty Statement Table of ContentsRules for Safe Operation Symbol MeaningKickback Safety Precautions Safety and International Symbols Chain Components Kickback Specifics Read ALL Instructions Important Safety InstructionsPage Save These Instructions Pole SAW Trimming PrecautionsAssembly Instructions Adjusting Pole Length Assembly of Pole SAWCutting with the Pole SAW Oiling ChainFilling OIL Tank Selecting the Proper Extension Cord for Your SAW ModelCutting with only the Chain SAW Operating InstructionsTo Stop Motor Chain and BAR Lubrication No Serviceable Parts InsideExtension Cords Double InsulationTrimming a Tree Pruning General Cutting InstructionsFelling Felling a TreeFelling CUT General Guidelines for Felling TreesLimbing Bucking Using a SawhorseBucking Vertical CuttingGuide BAR Maintenance Maintenance InstructionsChain Maintenance Instructions Chain Tension Preventative MaintenanceBreaking in a NEW SAW Chain Servicing a Double Insulated ApplianceParts No Description Parts ListMTD LLC Manuel de L’utilisateur Declaration DE Garantie Table DES MatièresRègles DE Sécurité Alerte DE SécuritéAvertissement Les rebonds Symboles DE Sécurité ET Internationaux Dispositifs DE Securite Avertissement Lesrebonds Lire Toutes LES Instructions Instructions DE Surete ImportantesNutiliser Aucun Autre Accesoire OU Conserver CES Instructions Deballage Instructions D’ASSEMBLEEMontage D’ELEMENTS Reglage DE LA Tension DE LA ChaineReglage DE LA Longueur DE LA Canne Montage DE LA Perche ElagueuseCoupe a L’AIDE DE LA Perche Elagueuse Lubrefacation DE LA ChaineRemplissage DU Reservoir a Huile Choix D’UN Prolongateur Electrique ApproprieDemarrage DE LA Perche Elagueuse Consignes D’UTILISATIONArret DU Moteur Prolongateurs Electriques Lubrification DE LA Chaine ET DU DUIDE-CHAINEAucune Piece Interne Reparable Ailler UN Arbre Elaguar Instructions DE Decoupage GeneralesAbattage Abattage D’UN ArbreTrait D’ABATTAGE Regles Generales a Observer Pour L’ABATTAGETronconnage SUR Chevalet EbranchageTronconnage Coupe VerticaleEntretien DU GUIDE-CHAINE Instructions D’ENTRETIENEntretien DE LA Chaine Rodage D’UNE Nouvelle Chaine DE Tronconneuse Tension DE LA ChaineEntretien Preventif Reparation D’UN Appareil a Double ISOLA- TionRОfОrence Liste DES PiècesGarantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Declaración DE Garantía ÍndiceNormas DE Seguridad Alerta DE SeguridadAdvertencia El con Simbolos DE Seguridad E Internacionales Aspectos DE Seguridad Advertencia LEA Todas LAS LAS Instrucciones Instrucciones DE Seguridad ImportantesPage Precauciones DE Corte CON LA SIER- RA Telescopica Guarde Estas InstruccionesInstrucciones DE Asamblea Ensamble DE LA Motosierra TELE- Scopica Adjustando LA Longitude DE EL TuboCortando CON LA Motosierra Tele Scopica Aceitar LA CadenaLlenando EL Tanque DE Aceite Seleccionando EL Cable DE Extension CorrectoPara Arrancar LA Sierra Instrucciones DE FuncionamienttoPara Apagar EL Motor Cables DE Extension Lubricacion DE Barra Y CadenaAislacion Doble Podando UN Arbol Instrucciones DE Corte GeneralesTalado Desramando UN ArbolCorte DE Talado Reglas Generales Para EL Talado DE ArbolesLeñado DesramadoLeñado Usando UN Caballete Para Aserrar Cortando VerticalmenteMantenimiento DE LA Barra Guia Instrucciones DEL MantenimientoInstrucciones DE Mantenimiento DE LA Cadena Acondicionamiento EN UNA Cadena Para Sierra Nueva Tension DE LA SierraMantenimiento Preventivo Servicio AL Aparato DE Aislado DobleLista DE Piezas Nota MTD LLC Stop

PS specifications

MTD PS, or Machine Translation Deep Post-Editing System, is an innovative solution designed to improve the accuracy and quality of machine-generated translations. This system is particularly instrumental for businesses and organizations that rely on multilingual communication and require high-quality translations for documents, websites, and other materials.

One of the main features of MTD PS is its deep learning architecture, which employs neural networks to analyze and refine machine-generated translations. This technology allows the system to understand linguistic nuances, context, and semantics, resulting in translations that are not only grammatically correct but also culturally relevant. The adaptability of deep learning means that the system can continuously improve over time by learning from user feedback and various language data.

Another significant characteristic of MTD PS is its user-friendly interface. Designed with usability in mind, the system allows post-editors to review and enhance translations with ease. Suggestions for improvements are generated in real-time, enabling human translators to make quick decisions and apply necessary changes. This collaboration between humans and machines amplifies productivity while maintaining high standards of quality.

MTD PS integrates advanced natural language processing (NLP) technologies, which are crucial for understanding and generating human-like text. With features such as context-aware formatting and terminology management, the system ensures consistency across different translations, streamlining the localization process. NLP capabilities also facilitate the handling of idiomatic expressions and jargon specific to certain fields, enabling the system to cater to various industries.

Additionally, MTD PS is equipped with extensive data analytics features. It allows users to track performance metrics such as translation accuracy and editor efficiency. This data-driven approach helps organizations evaluate the effectiveness of their translation processes and make informed decisions about future localization strategies.

In summary, MTD PS is a powerful tool that leverages deep learning, NLP technologies, and user-centric design to enhance the quality of machine translations. Its ability to adapt, learn, and provide actionable insights makes it an invaluable asset for a wide range of applications in the global marketplace. As businesses continue to expand their reach across borders, systems like MTD PS will play a pivotal role in ensuring effective communication and fostering collaboration across cultures.