MTD PS manual Assembly Instructions

Page 11

ASSEMBLY INSTRUCTIONS

INTRODUCTION

This unit is designed for occasional homeowner use and should not be used for commercial purposes or subjected to heavy continuous use.

Your new chain saw can be used for a variety of projects such as cutting firewood, making fence posts, felling small trees, limbing, pruning at ground level, and light carpentry. Cut only wood or wood products with your saw.

UNPACKING

1.Remove all items from carton.

2.Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought the pole saw.

ASSEMBLY REQUIREMENTS

Your new pole saw will require adjustment of chain and fill- ing the oil tank with lubricating oil before the unit is ready for operation. Do not start the saw motor until the unit is properly prepared.

Read all instructions carefully. Do not install any other size bar and chain than what is recommended for your model.

GUIDE BAR / SAW CHAIN REPLACEMENT INSTALLATION..

Whenever handling the WARNING: saw chain, wear work

gloves for protection against sharp cut ting edges.

1.Remove bar nuts, push bar bolts in and slide sprocket support down. (See Fig. 3)

2.Remove old guide bar and chain.

3.Using a straight screwdriver, turn the chain adjustment screw counterclockwise as far as it will go, or until tang is to the end of its travel.

4.Loop saw chain over drive sprocket with the cutting edges of the chain pointing in the direction of rotation.

5.Place the slotted end of guide bar over the bar bolt so the tang fits into the lower hole in the guide guide bar.

6.Make sure the chain follows the slot in the guide bar. Slide the sprocket support up and push the bar bolts through the sprocket support.

7.Install the bar retaining nuts hand tight, (Proceed to saw chain tension Adjustment).

Guide Bar Bolts

Boulons du guide-chaîne

Tornillos de la Barra Guia

Saw Chain

Chaîne

Motosierra

 

Guide Bar

 

Guide-chaîne

 

Barra Guia

 

Adjusting Hole

 

Orifice de réglage

 

Orificio de Ajuste

Drive Sprocket

Guide Bar Nuts

Ecrous du guide-chaîne

Pignon d’entraîne-

Tuercas de Barra Guia

ment

 

Engrane

 

 

Adjusting Plate

 

Plaque de

Tang

réglage

Tenen

Placa de Ajuste

Espiga

Adjusting Screw

 

 

Vis de réglage

 

Tornillo de

 

Ajuste

 

Sprocket Support

 

Support du pignon

 

Soporte del

 

Engrane

Fig.3

SAW CHAIN TENSION ADJUSTMENT

Proper tension of the saw chain is extremely important and must be checked before starting, as well as during, any cut- ting operation. Taking the time to make needed adjust- ments to the saw chain will result in improved cutting per- formance and prolonged chain life.

NOTE: A new chain and bar will need readjustment after as few as 5 cuts. This is normal during the break-in period, and the interval between future adjustments will lengthen quickly (Figure 5).

If a chain is TOO LOOSE CAUTION: or TOO TIGHT, the bar chain and saw bearings

will wear more rapidly. Study Figure 4 for infor- mation concerning correct cold tension (A), correct warm tension (B), and as a guide for when saw chain needs adjustment (C).

TO ADJUST SAW CHAIN TENSION:

1.Loosen the bar retaining nuts (D) so they are hand tight. (See Fig. 4)

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Warranty Statement Table of ContentsRules for Safe Operation Symbol MeaningKickback Safety Precautions Safety and International Symbols Chain Components Kickback Specifics Read ALL Instructions Important Safety InstructionsPage Save These Instructions Pole SAW Trimming PrecautionsAssembly Instructions Adjusting Pole Length Assembly of Pole SAWSelecting the Proper Extension Cord for Your SAW Model Oiling ChainCutting with the Pole SAW Filling OIL TankTo Stop Motor Operating InstructionsCutting with only the Chain SAW Double Insulation No Serviceable Parts InsideChain and BAR Lubrication Extension CordsFelling a Tree General Cutting InstructionsTrimming a Tree Pruning FellingFelling CUT General Guidelines for Felling TreesVertical Cutting Bucking Using a SawhorseLimbing BuckingChain Maintenance Instructions Maintenance InstructionsGuide BAR Maintenance Servicing a Double Insulated Appliance Preventative MaintenanceChain Tension Breaking in a NEW SAW ChainParts No Description Parts ListMTD LLC Manuel de L’utilisateur Declaration DE Garantie Table DES MatièresRègles DE Sécurité Alerte DE SécuritéAvertissement Les rebonds Symboles DE Sécurité ET Internationaux Dispositifs DE Securite Avertissement Lesrebonds Lire Toutes LES Instructions Instructions DE Surete ImportantesNutiliser Aucun Autre Accesoire OU Conserver CES Instructions Reglage DE LA Tension DE LA Chaine Instructions D’ASSEMBLEEDeballage Montage D’ELEMENTSReglage DE LA Longueur DE LA Canne Montage DE LA Perche ElagueuseChoix D’UN Prolongateur Electrique Approprie Lubrefacation DE LA ChaineCoupe a L’AIDE DE LA Perche Elagueuse Remplissage DU Reservoir a HuileArret DU Moteur Consignes D’UTILISATIONDemarrage DE LA Perche Elagueuse Aucune Piece Interne Reparable Lubrification DE LA Chaine ET DU DUIDE-CHAINEProlongateurs Electriques Abattage D’UN Arbre Instructions DE Decoupage GeneralesAiller UN Arbre Elaguar AbattageTrait D’ABATTAGE Regles Generales a Observer Pour L’ABATTAGECoupe Verticale EbranchageTronconnage SUR Chevalet TronconnageEntretien DE LA Chaine Instructions D’ENTRETIENEntretien DU GUIDE-CHAINE Reparation D’UN Appareil a Double ISOLA- Tion Tension DE LA ChaineRodage D’UNE Nouvelle Chaine DE Tronconneuse Entretien PreventifRОfОrence Liste DES PiècesGarantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Declaración DE Garantía ÍndiceNormas DE Seguridad Alerta DE SeguridadAdvertencia El con Simbolos DE Seguridad E Internacionales Aspectos DE Seguridad Advertencia LEA Todas LAS LAS Instrucciones Instrucciones DE Seguridad ImportantesPage Precauciones DE Corte CON LA SIER- RA Telescopica Guarde Estas InstruccionesInstrucciones DE Asamblea Ensamble DE LA Motosierra TELE- Scopica Adjustando LA Longitude DE EL TuboSeleccionando EL Cable DE Extension Correcto Aceitar LA CadenaCortando CON LA Motosierra Tele Scopica Llenando EL Tanque DE AceitePara Apagar EL Motor Instrucciones DE FuncionamienttoPara Arrancar LA Sierra Aislacion Doble Lubricacion DE Barra Y CadenaCables DE Extension Desramando UN Arbol Instrucciones DE Corte GeneralesPodando UN Arbol TaladoCorte DE Talado Reglas Generales Para EL Talado DE ArbolesCortando Verticalmente DesramadoLeñado Leñado Usando UN Caballete Para AserrarInstrucciones DE Mantenimiento DE LA Cadena Instrucciones DEL MantenimientoMantenimiento DE LA Barra Guia Servicio AL Aparato DE Aislado Doble Tension DE LA SierraAcondicionamiento EN UNA Cadena Para Sierra Nueva Mantenimiento PreventivoLista DE Piezas Nota MTD LLC Stop

PS specifications

MTD PS, or Machine Translation Deep Post-Editing System, is an innovative solution designed to improve the accuracy and quality of machine-generated translations. This system is particularly instrumental for businesses and organizations that rely on multilingual communication and require high-quality translations for documents, websites, and other materials.

One of the main features of MTD PS is its deep learning architecture, which employs neural networks to analyze and refine machine-generated translations. This technology allows the system to understand linguistic nuances, context, and semantics, resulting in translations that are not only grammatically correct but also culturally relevant. The adaptability of deep learning means that the system can continuously improve over time by learning from user feedback and various language data.

Another significant characteristic of MTD PS is its user-friendly interface. Designed with usability in mind, the system allows post-editors to review and enhance translations with ease. Suggestions for improvements are generated in real-time, enabling human translators to make quick decisions and apply necessary changes. This collaboration between humans and machines amplifies productivity while maintaining high standards of quality.

MTD PS integrates advanced natural language processing (NLP) technologies, which are crucial for understanding and generating human-like text. With features such as context-aware formatting and terminology management, the system ensures consistency across different translations, streamlining the localization process. NLP capabilities also facilitate the handling of idiomatic expressions and jargon specific to certain fields, enabling the system to cater to various industries.

Additionally, MTD PS is equipped with extensive data analytics features. It allows users to track performance metrics such as translation accuracy and editor efficiency. This data-driven approach helps organizations evaluate the effectiveness of their translation processes and make informed decisions about future localization strategies.

In summary, MTD PS is a powerful tool that leverages deep learning, NLP technologies, and user-centric design to enhance the quality of machine translations. Its ability to adapt, learn, and provide actionable insights makes it an invaluable asset for a wide range of applications in the global marketplace. As businesses continue to expand their reach across borders, systems like MTD PS will play a pivotal role in ensuring effective communication and fostering collaboration across cultures.
Top Page Image Contents