MTD PS manual

Page 9

A. GRIP SAW FIRMLY: Hold the chain saw firmly with

both hands when the motor is running. Keep a good firm grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle.

B. Do not over reach.

C. Keep proper footing and balance at all times.

D. Do not let the nose of the guide bar contact a log, branch, ground or other obstruction.

E. Do not cut above shoulder height.

F.Use devices, such as low-kickback chain, guide bar nose guards, chain brakes and special guide bars, which reduce the risks associated with kickback.

G.Use only replacement bars and chains specified by the manufacturer or the equivalent.

H.There are no other replacement components for achieving kickback protection in accordance with CSA Z62.3.

20.POWER SUPPLY: Connect the chain saw to correct voltage; be sure that the voltage supplied is the same as that specified on the nameplate of the tool.

21.DO NOT operate a chain saw that is damaged, improperly adjusted, or not completely and securely assembled. Be sure that the saw chain stops moving when the trigger is released.

22.DO NOT attempt operations beyond your capacity or experience.

23.DO NOT operate a chain saw with one hand! Serious injury to the operator, helpers, or bystanders may result from one-handed operation. A chain saw is intended for two-handed use.

24.TO REDUCE potential for electric shock, do not oper- ate the saw on wet or slippery surfaces, or during snow storms, rain storms, and other adverse weather conditions.

25.DO NOT allow dirt, debris or sawdust to build up on the motor or outside air vents.

26.Follow the manufacturer’s sharpening and mainte- nance instructions for the saw chain.

27.Cut at high motor speeds.

28.Operation of a chain saw should be restricted to mature, properly instructed individuals.

29.Your chain saw is intended for occasional homeowner use. It is not made for heavy continuous use.

30.DO NOT FORCE a small saw to do a job requiring a heavier duty unit.

31.EXAMINE THE ELECTRICAL SWITCHES. Do not use the chain saw if the switches do not properly turn on and off. Do not attempt to make any repairs to the electric switches. Take your saw to a MTD Authorized Service Center.

32.MAINTAIN EXTENSION CORDS. Inspect the exten- sion cords periodically and replace if damaged. Only use power cords that are suitably marked for outdoor use.

33.DO NOT OPERATE YOUR CHAIN SAW near or around flammable liquids or gases, whether in or out of doors. An explosion and/or fire may result.

34.This electric powered saw is classified by CSA as a Class 2C saw. It is intended for infrequent use by homeowner’s, cottagers and campers, and for such general applications such as clearing, pruning, cutting firewood, etc. It is not intended for prolonged use. If the intended use involves prolonged periods of opera- tion, this may cause circulatory problems in the user’s hands due to vibration. It may be appropriate to use a saw having an anti-vibration feature.

35.NEVER REMOVE, modify or make inoperative any safety device furnished with your unit.

36.Safety clothing required by your safety organizations, government regulations, or your employer should be used; otherwise, snug fitting clothing, safety footwear, and hand and ear protection should be worn.

37.When felling, keep at least 2 tree lengths between yourself and your fellow workers.

38.All chain saw service, other than the items listed in the user manual safety and maintenance instructions, should be performed by competent chain saw person- nel. Do not attempt to repair it yourself; there are no user serviceable parts inside.

NOTE: Low-kickback saw chain is chain that has met the kickback performance requirements of ANSI B175.1-1991 and is in accordance with CSA Z62.3. Do not use other replacement chain unless it has met these requirements for your specific model.

39.DO NOT USE ANY OTHER CUTTING ATTACH- MENT OR ACCESSORIES. Use only MTD

replacement parts and accessories, which are designed specifically to enhance the performance and maximize the safe operation of our products. Failure to do so may cause poor performance and possible injury. Use only the chain and bar supplied with this product. Do not use any other cutting attachment. Use of such attachments will void your factory warranty and could result in serious bodily injury.

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operator’s Manual Warranty Statement Table of ContentsRules for Safe Operation Symbol MeaningKickback Safety Precautions Safety and International Symbols Chain Components Kickback Specifics Read ALL Instructions Important Safety InstructionsPage Save These Instructions Pole SAW Trimming PrecautionsAssembly Instructions Adjusting Pole Length Assembly of Pole SAWCutting with the Pole SAW Oiling ChainFilling OIL Tank Selecting the Proper Extension Cord for Your SAW ModelOperating Instructions Cutting with only the Chain SAWTo Stop Motor Chain and BAR Lubrication No Serviceable Parts InsideExtension Cords Double InsulationTrimming a Tree Pruning General Cutting InstructionsFelling Felling a TreeFelling CUT General Guidelines for Felling TreesLimbing Bucking Using a SawhorseBucking Vertical CuttingMaintenance Instructions Guide BAR MaintenanceChain Maintenance Instructions Chain Tension Preventative MaintenanceBreaking in a NEW SAW Chain Servicing a Double Insulated ApplianceParts No Description Parts ListMTD LLC Manuel de L’utilisateur Declaration DE Garantie Table DES MatièresRègles DE Sécurité Alerte DE SécuritéAvertissement Les rebonds Symboles DE Sécurité ET Internationaux Dispositifs DE Securite Avertissement Lesrebonds Lire Toutes LES Instructions Instructions DE Surete ImportantesNutiliser Aucun Autre Accesoire OU Conserver CES Instructions Deballage Instructions D’ASSEMBLEEMontage D’ELEMENTS Reglage DE LA Tension DE LA ChaineReglage DE LA Longueur DE LA Canne Montage DE LA Perche ElagueuseCoupe a L’AIDE DE LA Perche Elagueuse Lubrefacation DE LA ChaineRemplissage DU Reservoir a Huile Choix D’UN Prolongateur Electrique ApproprieConsignes D’UTILISATION Demarrage DE LA Perche ElagueuseArret DU Moteur Lubrification DE LA Chaine ET DU DUIDE-CHAINE Prolongateurs ElectriquesAucune Piece Interne Reparable Ailler UN Arbre Elaguar Instructions DE Decoupage GeneralesAbattage Abattage D’UN ArbreTrait D’ABATTAGE Regles Generales a Observer Pour L’ABATTAGETronconnage SUR Chevalet EbranchageTronconnage Coupe VerticaleInstructions D’ENTRETIEN Entretien DU GUIDE-CHAINEEntretien DE LA Chaine Rodage D’UNE Nouvelle Chaine DE Tronconneuse Tension DE LA ChaineEntretien Preventif Reparation D’UN Appareil a Double ISOLA- TionRОfОrence Liste DES PiècesGarantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Declaración DE Garantía ÍndiceNormas DE Seguridad Alerta DE SeguridadAdvertencia El con Simbolos DE Seguridad E Internacionales Aspectos DE Seguridad Advertencia LEA Todas LAS LAS Instrucciones Instrucciones DE Seguridad ImportantesPage Precauciones DE Corte CON LA SIER- RA Telescopica Guarde Estas InstruccionesInstrucciones DE Asamblea Ensamble DE LA Motosierra TELE- Scopica Adjustando LA Longitude DE EL TuboCortando CON LA Motosierra Tele Scopica Aceitar LA CadenaLlenando EL Tanque DE Aceite Seleccionando EL Cable DE Extension CorrectoInstrucciones DE Funcionamientto Para Arrancar LA SierraPara Apagar EL Motor Lubricacion DE Barra Y Cadena Cables DE ExtensionAislacion Doble Podando UN Arbol Instrucciones DE Corte GeneralesTalado Desramando UN ArbolCorte DE Talado Reglas Generales Para EL Talado DE ArbolesLeñado DesramadoLeñado Usando UN Caballete Para Aserrar Cortando VerticalmenteInstrucciones DEL Mantenimiento Mantenimiento DE LA Barra GuiaInstrucciones DE Mantenimiento DE LA Cadena Acondicionamiento EN UNA Cadena Para Sierra Nueva Tension DE LA SierraMantenimiento Preventivo Servicio AL Aparato DE Aislado DobleLista DE Piezas Nota MTD LLC Stop

PS specifications

MTD PS, or Machine Translation Deep Post-Editing System, is an innovative solution designed to improve the accuracy and quality of machine-generated translations. This system is particularly instrumental for businesses and organizations that rely on multilingual communication and require high-quality translations for documents, websites, and other materials.

One of the main features of MTD PS is its deep learning architecture, which employs neural networks to analyze and refine machine-generated translations. This technology allows the system to understand linguistic nuances, context, and semantics, resulting in translations that are not only grammatically correct but also culturally relevant. The adaptability of deep learning means that the system can continuously improve over time by learning from user feedback and various language data.

Another significant characteristic of MTD PS is its user-friendly interface. Designed with usability in mind, the system allows post-editors to review and enhance translations with ease. Suggestions for improvements are generated in real-time, enabling human translators to make quick decisions and apply necessary changes. This collaboration between humans and machines amplifies productivity while maintaining high standards of quality.

MTD PS integrates advanced natural language processing (NLP) technologies, which are crucial for understanding and generating human-like text. With features such as context-aware formatting and terminology management, the system ensures consistency across different translations, streamlining the localization process. NLP capabilities also facilitate the handling of idiomatic expressions and jargon specific to certain fields, enabling the system to cater to various industries.

Additionally, MTD PS is equipped with extensive data analytics features. It allows users to track performance metrics such as translation accuracy and editor efficiency. This data-driven approach helps organizations evaluate the effectiveness of their translation processes and make informed decisions about future localization strategies.

In summary, MTD PS is a powerful tool that leverages deep learning, NLP technologies, and user-centric design to enhance the quality of machine translations. Its ability to adapt, learn, and provide actionable insights makes it an invaluable asset for a wide range of applications in the global marketplace. As businesses continue to expand their reach across borders, systems like MTD PS will play a pivotal role in ensuring effective communication and fostering collaboration across cultures.
Top Page Image Contents