Honda Power Equipment MM60 SET-UPAND Assembly, Finish by tightening two 26 mm flange locknuts

Page 13

SET-UPAND ASSEMBLY

MOUNTING MOWER LIFT SYSTEM

Installwith the tractor on level ground.

Lock the parking brake, set the transmission lever in "N"(Neutral) and the P i 0 clutch lever in the "OFF" position. Set Lift Control lever to "DOWN" and turn Lowering Speed Control knob fully counter-clockwise ("FAST"). This allows you to pull the rear lift arms down by hand and makes assem- bly easier.

Installing Mower Lift Plate to Tractor

1.Remove drawbar assembly; this is bolted onto the transmission housing below the Rear PTO. Retain bolts, nuts and spacers for installation of lift plate assembly. Remove any dirt and debris from bottom of transmission housing and make sure bolt holes and screw threads are clean.

2.Assemble Y-lift bracket to lift plate assembly. Raised flange on lift plate assembly will face rear of tractor. Insert Y-lift bracket so that fork of Y faces front of tractor.

3.Attach mower lift plate assembly to tractor, passing the two projecting stud bolts on the transmission housing through the holes in the lift plate flange. Slide on 2 spacers previously removed and hand tighten both 26 mm flange locknuts.

4.Reach beneath the mower lift plate assembly and carefully insert the four 12 mm x 32 mm bolts through holes in lift plate assembly and into threaded holes on bottom of transmission housing. Housing is made of aluminum, so start bolts by hand to guard against cross threading. Tighten to 7 kg-m (50 ft-lb).

 

5. Finish by tightening two 26 mm flange locknuts

Mower Lift Plate

 

on projecting studs to 7 kg-m (50 ft-lb).

 

 

 

Wear heavy gloves to protect

 

your hands when installing lift link kit and

 

mower deck.

 

 

 

Lifting system can crush fingers

 

 

and

hands, so keep them clear of links and

 

lift arms when operating.

 

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Page To the Owner IntroductionGeneral INFORMATlON IntroductionContents Operate equipment Safety InformationPreparation Safety InformationBlock mower securely for storage Maintenance SafetyReplace immediately if damaged Safety InformationSET-UP and Assembly SET-UP and Assembly Point out safety features, shielding and options SET-UP and AssemblyPre-Delivery Check List Dealer Responsibility Finish by tightening two 26 mm flange locknuts SET-UPAND AssemblyLift Unk SET-UP and Assembly ‘y85 mm With Three Point Assemble both right and left brackets Subassembling Front Link BracketsMounting Front Link Bracket to.Tractor Installing Deck Hooks Installing MowerLevel the mower to assure proper cut. Mower Installing Front Anti-ScalpingRoller Installing MowerRemove level plug Add oil until it seeps out level plug hole Install both plugsAttaching Front Mower Links To Mower Side. Insert linchpin to lock~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Tor to 4-wheel drive position Switch off engine after moving tractor off mower. Set brakesOperation Operation PRE-OPERATION Check List Tours A small area Operating Your Mower with Other Equipment Installing Mower‘ by mower deck hook Install attachment as needed Owner Service MaintenanceDriveshaft U-joints Hrs Caster Pivot Hrs Caster Wheel Blade SpindlesDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Servicing Blade InstallationMaintenance Belt Assembly Maintenance Sleeve Bearing cone Housing and cups Cup Shaft Spindle assembly @Remove bearing cone from shaft Spindle AssemblyProper adjustment is attained T1I Yoke Journal cross Seal Snap ring Cup and bearings Universal Joint AssemblyAndhammer L11Remove gearbox from stand Gearbox MaintenanceGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageProblem TroubleshootingSolution Troubleshooting Specifications Owner Satisfaction Warranty Service
Top Page Image Contents