Honda Power Equipment MM60 manual Installing Mower, Attaching Front Mower Links to Front Bracket

Page 25

INSTALLING MOWER

Attaching Front Mower Links to Front

Bracket

1. Pull back on quick release pin in right or left front link bracket and twist until the spring pin catches in slot. Raise front mower link to bracket and line up holes. Lookingfrom inside the bracket, check alignment of holes.

2. If the holes in the bracket and the front link do not line up, twist front deck link by screwing it in or out to adjust length. If link is too long, turn clockwise to shorten. If link is too short, turn counterclockwise.to lengthen. Adjust both links an equal number of turns.

3. When the holes line up, pull quick release pin

 

towards you and turn to release spring pin

Front Mower Links Attach to Front Bracket

from slot. Make sure that quick release pin is

 

fully inserted through the holes inside the frame

 

bracket.

 

Attaching Driveline to.Mid-PT0

1.Engine should be OFF with key removed before attaching U-joint to Mid-PTO.

NOTE: The mower drive shaft is a 2-piece assem- bly. The inner shaft can be removed from the outer shaft. They fit together in only one way. A red paint dot on each section marks the blind spines which must be aligned.

2.Set the PTO Selector to the REAR position before attaching (this allows the Mid-PTO to turn freely).

3.Line up U-joint with shaft of the Mid-PTO. Splines will engage when correctly lined up. Pull back spring loaded locking collar on U- joint (towardsthe mower deck) as illustrated to insert U-joint into Mid-PTO. Slip U-joint into shaft until a click is heard.

U-joint Attaches to Mid-PTO

Once the connection is made, shake the driie shaft to be certain that the locking collar is for- ward and completely locked.

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Page Page To the Owner IntroductionGeneral INFORMATlON IntroductionContents Operate equipment Safety InformationPreparation Safety InformationBlock mower securely for storage Maintenance SafetyReplace immediately if damaged Safety InformationSET-UP and Assembly SET-UP and Assembly Point out safety features, shielding and options SET-UP and AssemblyPre-Delivery Check List Dealer Responsibility Finish by tightening two 26 mm flange locknuts SET-UPAND AssemblyLift Unk SET-UP and Assembly ‘y85 mm With Three Point Assemble both right and left brackets Subassembling Front Link BracketsMounting Front Link Bracket to.Tractor Installing Deck Hooks Installing MowerLevel the mower to assure proper cut. Mower Installing Front Anti-ScalpingRoller Installing MowerRemove level plug Add oil until it seeps out level plug hole Install both plugsAttaching Front Mower Links To Mower Side. Insert linchpin to lock~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Tor to 4-wheel drive position Switch off engine after moving tractor off mower. Set brakesOperation Operation PRE-OPERATION Check List Tours A small area Operating Your Mower with Other Equipment Installing Mower‘ by mower deck hook Install attachment as needed Owner Service MaintenanceDriveshaft U-joints Hrs Caster Pivot Hrs Caster Wheel Blade SpindlesDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Servicing Blade InstallationMaintenance Belt Assembly Maintenance Sleeve Bearing cone Housing and cups Cup Shaft Spindle assembly @Remove bearing cone from shaft Spindle AssemblyProper adjustment is attained T1I Yoke Journal cross Seal Snap ring Cup and bearings Universal Joint AssemblyAndhammer L11Remove gearbox from stand Gearbox MaintenanceGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageProblem TroubleshootingSolution Troubleshooting Specifications Owner Satisfaction Warranty Service
Top Page Image Contents