Honda Power Equipment MM60 manual Blade Servicing, Blade Installation

Page 41

MAINTENANCE

~~

BLADE SERVICING

Inspect blades for condition and proper installa- tion each time before operation. Replace any blade that is bent, excessively nicked, worn or has any other damage. Small.nickscan be giound out when sharpening.

Blade Removal

For right and left spindles, install spindle lock wrench (5) through belt shield and into holes in spindle pulley as shown. Remove bolt which has RIGHT HAND THREADS. Remove cup washers, washer and blade.

On the center spindle use blade wrench handle. The handle will rotate against gearbox stand

.whenblade bolt is removed.

Shoulder washer will not normally come off unless intentionally removed.

Blade Installation

1.Install spindle lock wrench through belt shield and into holes in spindle pulley as shown.

2.Installshoulder washer (if removed) small end up. Make sure blade cutting edge is positioned

,. to lead in clockwise rotation, as viewed from top of mower.

3.Excessive blade slipping can cause cup washers to burn and lose their clamping force, Inspect cup washers to determine if they are burned or have lost their clamping force. Replace as necessary.

Use a new Nylok blade bolt when you replace the blade. Do not substi- tute any other bolt for the special blade bolt. It is self-locking, meeting the non-loosening requirementsfor this application.

4.Installtwo cup washers on bolt. Installwasher and blade on bolt. Remember bolt has right hand threads; install bolt and blade assembly into spindle. Torque bolt to 23.5 kg/m (170 ft,/ Ibs). Remove spindle lock wrench from pulley and shield.

1. Blade

2.Shoulder washer

3. Left belt shield

4.Spindle lock wrench

5.Spindle lock wrench handle

6.5/8"Standard flat washer

7.Cup washers

8.Blade bolt, special Nylok (right hand threads)

Blade Assembly

39

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Page Page To the Owner IntroductionGeneral INFORMATlON IntroductionContents Operate equipment Safety InformationPreparation Safety InformationBlock mower securely for storage Maintenance SafetyReplace immediately if damaged Safety InformationSET-UP and Assembly SET-UP and Assembly Pre-Delivery Check List Dealer Responsibility SET-UP and AssemblyPoint out safety features, shielding and options Finish by tightening two 26 mm flange locknuts SET-UPAND AssemblyLift Unk SET-UP and Assembly ‘y85 mm With Three Point Mounting Front Link Bracket to.Tractor Subassembling Front Link BracketsAssemble both right and left brackets Installing Deck Hooks Installing MowerLevel the mower to assure proper cut. Mower Installing Front Anti-ScalpingRoller Installing MowerRemove level plug Add oil until it seeps out level plug hole Install both plugsAttaching Front Mower Links To Mower Side. Insert linchpin to lock~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Tor to 4-wheel drive position Switch off engine after moving tractor off mower. Set brakesOperation Operation PRE-OPERATION Check List Tours A small area Operating Your Mower with Other Equipment Installing Mower‘ by mower deck hook Install attachment as needed Owner Service MaintenanceDriveshaft U-joints Hrs Caster Pivot Hrs Caster Wheel Blade SpindlesDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Servicing Blade InstallationMaintenance Belt Assembly Maintenance Sleeve Bearing cone Housing and cups Cup Shaft Spindle assembly @Remove bearing cone from shaft Spindle AssemblyProper adjustment is attained T1I Yoke Journal cross Seal Snap ring Cup and bearings Universal Joint AssemblyAndhammer L11Remove gearbox from stand Gearbox MaintenanceGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageSolution TroubleshootingProblem Troubleshooting Specifications Owner Satisfaction Warranty Service
Top Page Image Contents