Honda Power Equipment MM60 manual T1I

Page 48

MAINTENANCE

I

t1I

1.Spindle assembly

2.Seal

3.Sleeve

4.Bearing cone

5.Housing and cups

6.Cup

7.Shaft

Spindle Assembly

1O.Apply a thin coat of lubricant to bottom seal (2)

.. and install with spring up toward center of housing.

11.Place bottom seal squarely on housing. Select a piece of pipe or tubing with an OD that will set on outside edge of seal. A'tube that is too small will bow seal cage.

12.Carefully press seal into housing, preventing distortion to metal seal cage. Seal should seat firmly and squarely against machined shoulder in housing.

13.Make sure seal lip did not roll under. Distortion to seal cage or damage to seal lip will cause seal to leak. Damaged seals must be replaced.

14.Apply a thin coat of lubricant to top seal (2) anc installwith spring up away from center of housing. Top seal should be flush with top of housing.

15,Lubricate spindle with a lithium grease of #2 consistency with a MOLY (molybdenum disul- fide) additive. Vent top seal with a blunt edged tool such as a letter opener while filling with grease. Rotate housing on spindle shaft, checking for free movement.

Blade Spindle Installation

1.Insert spindle through bottom of mower deck and install three mounting bolts. Be sure to position grease fittings toward lubrication access areas. Refer to lubricationchart.

D E E E l Pulley installation sequence is very important for bearing life. Follow the sequence exactly.

2.Install pulley and split taper bushing with inte- gral key on spindle shaft. Install bolt and flat washer in top of spindle shaft. Torque this bolt to 1.7 kg/cm (12 Wlbs), then alternately tighten split taper bushing bolts to 1.7 kg/cm (12 Wlbs).

46

Image 48

Contents Page Page Introduction To the OwnerIntroduction General INFORMATlONContents Safety Information Operate equipmentSafety Information PreparationMaintenance Safety Block mower securely for storageSafety Information Replace immediately if damagedSET-UP and Assembly SET-UP and Assembly SET-UP and Assembly Point out safety features, shielding and optionsPre-Delivery Check List Dealer Responsibility SET-UPAND Assembly Finish by tightening two 26 mm flange locknutsLift Unk SET-UP and Assembly ‘y85 mm With Three Point Subassembling Front Link Brackets Assemble both right and left bracketsMounting Front Link Bracket to.Tractor Installing Mower Installing Deck HooksLevel the mower to assure proper cut. Mower Installing Mower Installing Front Anti-ScalpingRollerInstall both plugs Remove level plug Add oil until it seeps out level plug holeSide. Insert linchpin to lock Attaching Front Mower Links To Mower~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Switch off engine after moving tractor off mower. Set brakes Tor to 4-wheel drive positionOperation Operation PRE-OPERATION Check List Tours A small area Installing Mower Operating Your Mower with Other Equipment‘ by mower deck hook Install attachment as needed Maintenance Owner ServiceCaster Pivot Hrs Caster Wheel Blade Spindles Driveshaft U-joints HrsDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Installation Blade ServicingMaintenance Belt Assembly Maintenance Spindle assembly @ Sleeve Bearing cone Housing and cups Cup ShaftSpindle Assembly Remove bearing cone from shaftProper adjustment is attained T1I Universal Joint Assembly Yoke Journal cross Seal Snap ring Cup and bearingsL11 AndhammerGearbox Maintenance Remove gearbox from standGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageTroubleshooting ProblemSolution Troubleshooting Specifications Warranty Service Owner Satisfaction