Honda Power Equipment MM60 manual Installing Mower, Installing Front Anti-ScalpingRoller

Page 21

INSTALLING MOWER

NOTE: Tool is available (see illustration)for ease of measurement.

1, To level mower from side to side, measure distance from front blade tip to ground. For left and right blades, measurements should be within 5 mm.(1/4 in) of each other. Move washers as necessary to raise the low corner. To add washers, raise mower deck until wheels clear ground by about 5 in.

2.Place wood block or floor jack under edge of mower to hold it while wheel is removed. Drive out split pin from lower caster wheel to remove caster wheel shaft. Move washers to the bottom part of caster wheel shaft as illustrated . Each washer changes height by 3 mm (about 1/8 in).

3.Re-attachwheel, let mower down to rest on wheels, and re-measure. Repeat the adjustment until the differencebetween blade heights is approximately 5 mm (1/4 in). Do not replace split pin until after adjusting forward tilt.

4.Adjust forward tilt by measuring from front and rear of blades to ground. The front of the blades should be about 10 mm (3/8 in) lower than the rear of the blades. If difference is less than 5 mm (1/4 in) take washers from bottom of gauge wheel shaft and move to top. If difference in blade tip to ground measurementsis more than 15 mm (1/2 in), take washers from top of gauge wheel shaft and move to bottom as illustrated. Move equal numbers of washers for both left and right sides. Replace split pins.

Installing Front Anti-ScalpingRoller

1.Insert 1/2 x 5 in sleeve in wheel. Place 1/2 x 5 in. bolt through brackets for front anti-scalping roller and through sleeve as illustrated.

2.Secure with 1/2 in flanged hex locknut. Tighten locknut so that sides of bracket touch wheel sleeve without binding.

Mower Leveling Tool

HONDA Part No.

07JPJ-75001OA

W

Caster Wheels

W

Front Anti-Scalping Roller

1 9

Image 21
Contents Page Page To the Owner IntroductionGeneral INFORMATlON IntroductionContents Operate equipment Safety InformationPreparation Safety InformationBlock mower securely for storage Maintenance SafetyReplace immediately if damaged Safety InformationSET-UP and Assembly SET-UP and Assembly SET-UP and Assembly Point out safety features, shielding and optionsPre-Delivery Check List Dealer Responsibility Finish by tightening two 26 mm flange locknuts SET-UPAND AssemblyLift Unk SET-UP and Assembly ‘y85 mm With Three Point Subassembling Front Link Brackets Assemble both right and left bracketsMounting Front Link Bracket to.Tractor Installing Deck Hooks Installing MowerLevel the mower to assure proper cut. Mower Installing Front Anti-ScalpingRoller Installing MowerRemove level plug Add oil until it seeps out level plug hole Install both plugsAttaching Front Mower Links To Mower Side. Insert linchpin to lock~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Tor to 4-wheel drive position Switch off engine after moving tractor off mower. Set brakesOperation Operation PRE-OPERATION Check List Tours A small area Operating Your Mower with Other Equipment Installing Mower‘ by mower deck hook Install attachment as needed Owner Service MaintenanceDriveshaft U-joints Hrs Caster Pivot Hrs Caster Wheel Blade SpindlesDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Servicing Blade InstallationMaintenance Belt Assembly Maintenance Sleeve Bearing cone Housing and cups Cup Shaft Spindle assembly @Remove bearing cone from shaft Spindle AssemblyProper adjustment is attained T1I Yoke Journal cross Seal Snap ring Cup and bearings Universal Joint AssemblyAndhammer L11Remove gearbox from stand Gearbox MaintenanceGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageTroubleshooting ProblemSolution Troubleshooting Specifications Owner Satisfaction Warranty Service