Honda Power Equipment MM60 manual Installing Mower, Operating Your Mower with Other Equipment

Page 35

INSTALLING MOWER

OPERATING YOUR MOWER WITH OTHER EQUIPMENT

You may operate your ”60 mower with three- point hitch mounted attachments and with the FL6555 Front Loader sub frame only. You must not operate or install the mower while any other attachments are installed on the tractor.

A minimum 20% of tractor and equipment weight must be on tractor front wheels with mower in transport position.

Without this weight, tractor could tip over causing personal injury or death. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. When attaining the minimum 20% weight on the front wheels, you must not exceed the Roll Over Protection Structure (ROPS) weight certification. Weigh the tractor and equip- ment. Do not estimate.

Using Three-Point Hitch Attachments

1, Start the engine and set Lift Control Lever to “UP”and raise the mower to maximum height. Turn Lowering Speed Control fully clockwise to lock lift arms in up position. Leave Lift Control Lever in “UP” position. Stop engine, set brake and remove keys.

I! I Make sure to turn Lowering Speed Control fully clockwise to lock hydrau- lic system before attaching mower deck hook. This prevents the mower deck from descending and causing injury to feet or hands.

2.Pull linchpin holding mower hook to mower hook bracket. Turn mower hook in adjusting pin so that it is long enough to reach projecting lockup pin on bracket attached to tractor frame as illustrated.Adjust the mower hook so that it fits TIGHTLY over the projecting lockup pin on tractor. This will minimize the backlash on the lockup pin when it supports the mower.

3.Slip mower hook over lockup pin, and secure with washer and linchpin removedfrom mower hook bracket. Insert linchpin from front to back to lock properly.

I ’

Mower Hook Attaches to

Mower Hook Bracket

3 3

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Page Page To the Owner IntroductionGeneral INFORMATlON IntroductionContents Operate equipment Safety InformationPreparation Safety InformationBlock mower securely for storage Maintenance SafetyReplace immediately if damaged Safety InformationSET-UP and Assembly SET-UP and Assembly Pre-Delivery Check List Dealer Responsibility SET-UP and AssemblyPoint out safety features, shielding and options Finish by tightening two 26 mm flange locknuts SET-UPAND AssemblyLift Unk SET-UP and Assembly ‘y85 mm With Three Point Mounting Front Link Bracket to.Tractor Subassembling Front Link BracketsAssemble both right and left brackets Installing Deck Hooks Installing MowerLevel the mower to assure proper cut. Mower Installing Front Anti-ScalpingRoller Installing MowerRemove level plug Add oil until it seeps out level plug hole Install both plugsAttaching Front Mower Links To Mower Side. Insert linchpin to lock~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Tor to 4-wheel drive position Switch off engine after moving tractor off mower. Set brakesOperation Operation PRE-OPERATION Check List Tours A small area Operating Your Mower with Other Equipment Installing Mower‘ by mower deck hook Install attachment as needed Owner Service Maintenance30W Oil Oil Level Plug Caster Pivot Hrs Caster Wheel Blade SpindlesDriveshaft U-joints Hrs Driveshaft Slip Joint Hrs Spring Take-up Pivot ArmBlade Inspection Blade Servicing Blade InstallationMaintenance Belt Assembly Maintenance Sleeve Bearing cone Housing and cups Cup Shaft Spindle assembly @Remove bearing cone from shaft Spindle AssemblyProper adjustment is attained T1I Yoke Journal cross Seal Snap ring Cup and bearings Universal Joint AssemblyAndhammer L11Remove gearbox from stand Gearbox MaintenanceGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageSolution TroubleshootingProblem Troubleshooting Specifications Owner Satisfaction Warranty Service
Top Page Image Contents