Honda Power Equipment MM60 manual With Three Point

Page 17

SET-UP AND ASSEMBLY

Adjusting Lift Rod

(For Tractors With and Without Rear Three

Point Hitch)

Follow this procedure if you do not have a loader subframe installed.

Adjust the lift rod clearance by starting the engine, and shifting the Lift Control lever to "UP". Make sure hands are clear of lift arms before starting. Engine will not start unless operator is seated. Raise until lift arm reachestop or until resistance is encountered. If resistance is encountered,stop. Turn Lowering Speed control fully clockwise to lock arms up. Turn engine off. Grasp lift rods and check them for slack. They should be able to slide slightly on their pins. If there is no-slack in the lift rods, increaseclearance as illustrated.

Lifting system can be seriously damaged if arm presses against stop.

Adjusting Lift Rod

(Tractors With Rear Three Point Hitch)

To increase clearance turn bottom nut on adjuster counterclockwiseto loosen, slide down flange and then snug top nut. To decrease clearance, slide adjuster up as shown.

arm should not contact stopper

With Three Point

Adjusting Lift Rod

(Tractors Without Rear Thtee Point Hitch)

Turn the barrel of the lift rod by the projecting pins to shorten or lengthen the rod. Moveadjuster as required.The projecting pins must point side to side (transversely) when you are finished. If they don't, turn the barrel in the direction to increase clearance untilthey do.

Restart engine, move Lift Selector lever to "UP. When lift arms reach top position,stop engine, apply brakes and re-check clearance. Keep hands and fingers clear of lift system when operating to avoid injury. There should be slack in the linkage. If there is not, readjust as necessary.Tighten lock- nuts after adjusting both types of lift rods.

Without Three Point Hitch

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Page Page To the Owner IntroductionGeneral INFORMATlON IntroductionContents Operate equipment Safety InformationPreparation Safety InformationBlock mower securely for storage Maintenance SafetyReplace immediately if damaged Safety InformationSET-UP and Assembly SET-UP and Assembly Pre-Delivery Check List Dealer Responsibility SET-UP and AssemblyPoint out safety features, shielding and options Finish by tightening two 26 mm flange locknuts SET-UPAND AssemblyLift Unk SET-UP and Assembly ‘y85 mm With Three Point Mounting Front Link Bracket to.Tractor Subassembling Front Link BracketsAssemble both right and left brackets Installing Deck Hooks Installing MowerLevel the mower to assure proper cut. Mower Installing Front Anti-ScalpingRoller Installing MowerRemove level plug Add oil until it seeps out level plug hole Install both plugsAttaching Front Mower Links To Mower Side. Insert linchpin to lock~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Tor to 4-wheel drive position Switch off engine after moving tractor off mower. Set brakesOperation Operation PRE-OPERATION Check List Tours A small area Operating Your Mower with Other Equipment Installing Mower‘ by mower deck hook Install attachment as needed Owner Service MaintenanceDriveshaft U-joints Hrs Caster Pivot Hrs Caster Wheel Blade SpindlesDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Servicing Blade InstallationMaintenance Belt Assembly Maintenance Sleeve Bearing cone Housing and cups Cup Shaft Spindle assembly @Remove bearing cone from shaft Spindle AssemblyProper adjustment is attained T1I Yoke Journal cross Seal Snap ring Cup and bearings Universal Joint AssemblyAndhammer L11Remove gearbox from stand Gearbox MaintenanceGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageSolution TroubleshootingProblem Troubleshooting Specifications Owner Satisfaction Warranty Service
Top Page Image Contents