Honda Power Equipment MM60 manual Level the mower to assure proper cut. Mower

Page 20

INSTALLING MOWER

<

\

Front Caster Wheel

Rear Gauge Wheels \'@

Installing and Adjusting Wheels

1.Pull release pin on wheel yoke so that wheel

'arm can be raised to insert wheel. Assemble wheel by inserting 1/2 x 5 in. sleeve through wheel. Place 1/2 in. washer on 1/2 x 5 in. bolt and insert though yoke and sleeve in wheel.

.Securewith flanged locknut. Tighten locknut so - that sides of bracket touch wheel sleeve without binding. Do not over-tighten. Repeat for other front caster wheel.

2.Assemble the rear gauge wheels so that greasj fittings are to the inside for lubrication access. Raise rear of mower deck with lever or jack anc insertwood block beneath mower deck to support it while installing wheels. Insert sleeve through wheel. Placewasher on bolt and insert through sleeve in wheel and rear gauge wheel arm. Secure with flanged locknut. Tighten locknut so that sides of bracket touch wheel sleeve without binding. Do not over-tighten. Repeat for opposite side.

3.Raise front and rear wheels to middle position, insert pin in center hole of adjustment bracket. Cutting height will be 2.75 in. Level the mower ta assure proper cut. Mower also needs slight forward tilt. If adjusting wheels and blade height

after installing mower on tractor, make sure engine is off and key is removed before looking under mower.

m! a -Support mower deck solidly

while installing wheels. Keep fingers and feet clear'of deck until deck is firmly sup- ported.

Leveling the Mower

Level the mower to assure proper cut. Mower

needs slight (3/8in) forward tilt. If you are adjust- ing wheels and blade height after installing mower on tractor, make sure engine is off and key re- moved before looking under mower.

NOTE: Before measuring blade height, turn mower blades so that the right and left blades point towards front of mower.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Page Page Introduction To the OwnerIntroduction General INFORMATlONContents Safety Information Operate equipmentSafety Information PreparationMaintenance Safety Block mower securely for storageSafety Information Replace immediately if damagedSET-UP and Assembly SET-UP and Assembly Pre-Delivery Check List Dealer Responsibility SET-UP and AssemblyPoint out safety features, shielding and options SET-UPAND Assembly Finish by tightening two 26 mm flange locknutsLift Unk SET-UP and Assembly ‘y85 mm With Three Point Mounting Front Link Bracket to.Tractor Subassembling Front Link BracketsAssemble both right and left brackets Installing Mower Installing Deck HooksLevel the mower to assure proper cut. Mower Installing Mower Installing Front Anti-ScalpingRollerInstall both plugs Remove level plug Add oil until it seeps out level plug holeSide. Insert linchpin to lock Attaching Front Mower Links To Mower~~~ Attaching Front Mower Links to Front Bracket Lift Arms Fasten to Mower Deck Detaching Mower from Tractor Joint Detaches From Mid-PTO Switch off engine after moving tractor off mower. Set brakes Tor to 4-wheel drive positionOperation Operation PRE-OPERATION Check List Tours A small area Installing Mower Operating Your Mower with Other Equipment‘ by mower deck hook Install attachment as needed Maintenance Owner ServiceCaster Pivot Hrs Caster Wheel Blade Spindles Driveshaft U-joints HrsDriveshaft Slip Joint Hrs Spring Take-up Pivot Arm 30W Oil Oil Level PlugBlade Inspection Blade Installation Blade ServicingMaintenance Belt Assembly Maintenance Spindle assembly @ Sleeve Bearing cone Housing and cups Cup ShaftSpindle Assembly Remove bearing cone from shaftProper adjustment is attained T1I Universal Joint Assembly Yoke Journal cross Seal Snap ring Cup and bearingsL11 AndhammerGearbox Maintenance Remove gearbox from standGear Box Split taper bushing Drive pulley Gearbox stand Key Storage StorageSolution TroubleshootingProblem Troubleshooting Specifications Warranty Service Owner Satisfaction
Top Page Image Contents