Alamo JD-5425, JD-5525, JD-5225, JD-5205, JD-5105, JD-5325 manual Mount Kit Component Identification

Page 37

Mount Kit Component Identification

11.Install Operators Manual Cannister. The operator manual cannister bolts to the hydraulic tank on the side toward operator, this cannister should have the operators manual inside of it when shipped from the factory (See Figure 8). Note: The hydrau- lic tank has the return filter and directional control valve (Solenoid) already connected to it when shipped from the factory.

12.Install Valve Control Handle Mounting Brack- ets. The valve control stand weldment (P/N 107352) will bolt to the flat operators platform on the RH side. Install the mount stand where it will be convenient for the operator to use. The control stand weldment is adjustable for height, this is done by selecting the mounting hole you want to use. The stand can be cut for height adjustment if wanted. The valve control bracket (P/N 02977335) bolts the stand weldment using the holes that best fir the opera- tors needs (See Figure 9 & 10). Once the right dis- tance is decided to fit operator the valve control mount will bolt to the floor of the operators plat form with 4 bolts. The holes will need to drilled through the floor, check the under side of the floor before drilling any holes to make certain drill bit will not hit and damage anything (See Figure 11).

Motor Directional

Control Valve

Return Filter

Assembly

Operators Manual

 

Cannister

 

Figure 8

Hydraulic Tank

 

P/N 107352

 

Control Stand

 

Weldment

 

P/N 02977335

Valve Mount Brkt

Weldment

 

Figure 9

 

Figure 10

Figure 11

Switch Blade (JD-5105-5205-5225-5325-5425-5525, Asy. Man) 05/05

© 2005 Alamo Group Inc.

Section 4 - 5

Image 37
Contents Switchblade Page Page To the OWNER/OPERATOR/DEALER About this Manual IntroductionModel Specifications Index Assembly InstructionElectrical Connections Alamo Group Inc Section Do not Required of the Owner Safety RecommendationsRequired of the Operator Standard Specifications Switch Blade 5 ft. & 6 ft Using AN Adapter with a Torque Wrench Hose END Fitting Torque Specs Switch Blade General Information / Installation Requirements General Information Tractor, Area CleanlinessLeveling Tractor General Information / Installation Requirements Do not Weld On This Unit During or After Installation Section Use Existing Bolt & Lockwasher From Crankshaft Pulley Pump / Driveshaft Schematic 5425234 Pump / Driveline Schematic 5225 & 5325 CAB/ Rops234 Pump / Driveline Schematic 5105 & 5205 CAB/ RopsPump & Drive Shaft Installation Pump & Drive Shaft InstallationLower Plate Front END TOP Cccccccc JD-5425 & JD-5525 Machined Pump Typical Drive Shaft Installation Drive Shaft Installation 5105 & 5205 onlySwitchblade Frame Installation Frame Installation Carriage Arm Pivot Pin Tank Mounting Bolts Mount Kit Component Identification Alamo Group Inc Switchblade Two Spool Control Valve Control Valve & Valve Controls InstallationControl Valve & Hoses Rops HydraulicControl Valve & Hoses RopsHydraulicControl Valve & Hoses CAB HydraulicControl Valve & Hoses CAB Control Valve & Valve Controls Installation CAB Control Cable Connection to Control Stick Assemblies Control Valve & Valve Controls Installation Remote CablesPush / Pull & Reversing Toggle Switch Control Valve & Hoses HydraulicControl Valve & HosesHydraulic Connections / Hose Routing Single RH Wing ShownHydraulicPump Hose Connection Fill Hydraulic Tank with Oil Fill Hydraulic TankFill Hydraulic Tank Alamo Group Inc Electrical Connections Electrical Circuit RH Wing Mower Motor Pump Electrical CircuitMechanical Repairs & Adjustments Lead Adjustment Cutter BAR AdjustmentsPitch Adjustment Guard AdjustmentWear Plates Clips Knife ReplacementKnife Repair Cutter Bar Assembly Replacement Cutter BAR ReplacementKnife Bar Replacement Knife BAR Replacement123143431233 Knife ReplacementOuter Shoe Assembly Replacement Outer Shoe Assembly ReplacementInner Shoe Replacement Rock Guard, Clip & Wear Plate ReplacementInner Shoe Weldment Replacement Inner Shoe Weldment ReplacementInner Shoe Weldment Replacement Carriage Arm Assembly Replace- ment Carriage ARM Assembly ReplacementKnife Drive Assembly Repair / Replacement Knife Drive Repair / ReplacementKnife Drive Repair / Replacement Alamo Group Inc Switchblade Mount Kit Rops Flat Ioos Platform Only Mount Kit Component IdentificationWD & 4WD Rops W/ Flat Platform Mount Kit Bill of Material 5425 & 5525 CAB / RopsAbove items are included in Hydraulic Kit P/N Used On John Deere 5425/5525 CAB only / 2&4wd From Previous John Deere Used On John Deere 5225/5325 CAB only / 2&4wd Mount Kit Bill of Material 5225 & 5325 CAB / RopsAbove items are included in Hydraulic Kit P/N Pump Guard Kit, P/N 02983480 Consist of the Following Items Hydraulic Kit 02983099 Consist of the Following Items Used On John Deere 5225/5325 Rops / 2&4wd w/ Flat Platform ADP HYD Elbow 4MJ 4FJX 45DEG 5105/5205 ROPS/2&4wd Used On John Deere 5105/5205 Rops / 2&4wd Mount Kit Bill of Material 5105 & 5205 RopsOptions Pump Drive Schematic Pump / Driveline Schematic 5425 & 5525 CAB/ RopsBolts, P/N Lockwasher, P/N Crankshaft Pulley Adapter Bolts 4 Req Setscrew, P/N JD-5105 26.50 LG Hose Ring Mount Kit Component Identification Mount Kit Component Identification 5425 JD-5425 & JD-5525 Model Tractor Only JD-5225 & JD-5325 Model Tractor Only Mount Kit Component Identification 5225JD-5105 & JD-5205 Model Tractor Only Mount Kit Component Identification 5105Common Component Identification All Tractors Page Hydraulic Schematic RH Wing Only Hydraulic Schematic Dual RH & LH Wing Hydraulic Hose Routing Schematic Hydraulic Hose Routing Mount Kit Component Identification Page Switch Blade JD-5105-5205-5225-5325-5425-5525 Asy. Man /05