Alamo JD-5205, JD-5525, JD-5425, JD-5225 Control Valve & Valve Controls Installation Remote Cables

Page 45

Control Valve & Valve Controls Installation - Remote Cables

Control Cable Connection to Control Stick Assemblies:

1.First remove the Cross- Screw from the bottom of the Control Stick Assembly. DO NOT remove the screws that fasten the two housings halves together (See Figure 13).

2.Next holding the housing, fully shift the Handle in the Control Stick Assembly to expose the female-threaded end of the Plunger Rod (See Figure 14).

3.Then while holding the Handle to expose the Plunger Rod, thread the Threaded Bead of the Cable into the end of the Plunger Rod and tighten securely. Release the Handle, allowing the Cable to pull into the Control Stick Assembly (See Figure 15)

4.Once Cable is attached to Plunger Rod, move the handle to pull conduit sleeve up and into the control stick assembly (See Figure 16) The Conduit Sleeve has a groove in it that should align with the cross screw (See Figure 16)

5.Reinstall the Cross Screw making certain that the cross screw and conduit sleeve groove are in alignment. Tighten the cross screw securely (See Figure 17)

Control Stick

Assembly

Cross-Screw

Figure 13

Female Threaded

Plunger Rod

Figure 14

Figure 15

Threaded Bead

 

Cross-

 

Screw Hole

Figure 16

Conduit Sleeve

Switch Blade (JD-5105-5205-5225-5325-5425-5525, Asy. Man) 05/05

© 2005 Alamo Group Inc.

Section 5 - 7

Image 45
Contents Switchblade Page Page To the OWNER/OPERATOR/DEALER About this Manual IntroductionModel Specifications Index Assembly InstructionElectrical Connections Alamo Group Inc Section Do not Safety Recommendations Required of the OwnerRequired of the Operator Standard Specifications Switch Blade 5 ft. & 6 ft Using AN Adapter with a Torque Wrench Hose END Fitting Torque Specs Switch Blade General Information / Installation Requirements General Information Tractor, Area CleanlinessLeveling Tractor General Information / Installation Requirements Do not Weld On This Unit During or After Installation Section Use Existing Bolt & Lockwasher From Crankshaft Pulley Pump / Driveshaft Schematic 5425234 Pump / Driveline Schematic 5225 & 5325 CAB/ Rops234 Pump / Driveline Schematic 5105 & 5205 CAB/ RopsPump & Drive Shaft Installation Pump & Drive Shaft InstallationLower Plate Front END TOP Cccccccc JD-5425 & JD-5525 Machined Pump Typical Drive Shaft Installation Drive Shaft Installation 5105 & 5205 onlySwitchblade Frame Installation Frame Installation Carriage Arm Pivot Pin Tank Mounting Bolts Mount Kit Component Identification Alamo Group Inc Switchblade Two Spool Control Valve Control Valve & Valve Controls InstallationControl Valve & Hoses Rops HydraulicControl Valve & Hoses RopsHydraulicControl Valve & Hoses CAB HydraulicControl Valve & Hoses CAB Control Valve & Valve Controls Installation CAB Control Cable Connection to Control Stick Assemblies Control Valve & Valve Controls Installation Remote CablesPush / Pull & Reversing Toggle Switch Control Valve & Hoses HydraulicControl Valve & HosesHydraulic Connections / Hose Routing Single RH Wing ShownHydraulicPump Hose Connection Fill Hydraulic Tank with Oil Fill Hydraulic TankFill Hydraulic Tank Alamo Group Inc Electrical Connections Electrical Circuit RH Wing Mower Motor Pump Electrical CircuitMechanical Repairs & Adjustments Lead Adjustment Cutter BAR AdjustmentsPitch Adjustment Guard AdjustmentWear Plates Knife Replacement ClipsKnife Repair Cutter Bar Assembly Replacement Cutter BAR ReplacementKnife Bar Replacement Knife BAR Replacement123143431233 Knife ReplacementOuter Shoe Assembly Replacement Outer Shoe Assembly ReplacementInner Shoe Replacement Rock Guard, Clip & Wear Plate ReplacementInner Shoe Weldment Replacement Inner Shoe Weldment ReplacementInner Shoe Weldment Replacement Carriage Arm Assembly Replace- ment Carriage ARM Assembly ReplacementKnife Drive Assembly Repair / Replacement Knife Drive Repair / ReplacementKnife Drive Repair / Replacement Alamo Group Inc Switchblade Mount Kit Rops Flat Ioos Platform Only Mount Kit Component IdentificationWD & 4WD Rops W/ Flat Platform Mount Kit Bill of Material 5425 & 5525 CAB / RopsAbove items are included in Hydraulic Kit P/N Used On John Deere 5425/5525 CAB only / 2&4wd From Previous John Deere Used On John Deere 5225/5325 CAB only / 2&4wd Mount Kit Bill of Material 5225 & 5325 CAB / RopsAbove items are included in Hydraulic Kit P/N Pump Guard Kit, P/N 02983480 Consist of the Following Items Hydraulic Kit 02983099 Consist of the Following Items Used On John Deere 5225/5325 Rops / 2&4wd w/ Flat Platform ADP HYD Elbow 4MJ 4FJX 45DEG 5105/5205 ROPS/2&4wd Used On John Deere 5105/5205 Rops / 2&4wd Mount Kit Bill of Material 5105 & 5205 RopsOptions Pump Drive Schematic Pump / Driveline Schematic 5425 & 5525 CAB/ RopsBolts, P/N Lockwasher, P/N Crankshaft Pulley Adapter Bolts 4 Req Setscrew, P/N JD-5105 26.50 LG Hose Ring Mount Kit Component Identification Mount Kit Component Identification 5425 JD-5425 & JD-5525 Model Tractor Only JD-5225 & JD-5325 Model Tractor Only Mount Kit Component Identification 5225JD-5105 & JD-5205 Model Tractor Only Mount Kit Component Identification 5105Common Component Identification All Tractors Page Hydraulic Schematic RH Wing Only Hydraulic Schematic Dual RH & LH Wing Hydraulic Hose Routing Schematic Hydraulic Hose Routing Mount Kit Component Identification Page Switch Blade JD-5105-5205-5225-5325-5425-5525 Asy. Man /05