Monitoring the Front Panel | 3Com 5102M-FBP, 5104M-FB1, 510M-FBP

This display tells you the status of the specific port. It includes the management and dip switch settings from the board.

The following command displays detailed information about the 10BASE-FB Module in slot 8 of the concentrator.

ONline> show module 8 verbose

[ENTER]

Port Display for Module 5104M-FB1:

Slot	Module	Version	Network		General Information
08	5104M-FB1	00x		ISOLATED	ETHERNET_2
5104M-FB1: ONline Ethernet 10BASE-FB Module
Network Dip Setting:				ETHERNET_1
Low Light Warning:				DISABLED
Low Light Warning Dip Setting:				DISABLED

This display tells you the status of the specific module. It includes the management and dip switch settings from the board.

For more information on the SHOW commands, refer to the:

❑Appropriate ONline management module installation and operation guide

❑ONline Management Commands Guide

Monitoring the Front Panel

The LEDs on the front panel of the 10BASE-FB Module allow you to monitor the status of each port. The 10BASE-FB Module has 10 LEDs on the front panel that allow you to monitor diagnostic, activity, and redundancy status for each port. Figure 3-4 shows the locations of these indicators.

Installing and Operating the Module 3 - 19

Image 75

3Com 5102M-FBP, 5104M-FB1, 510M-FBP installation and operation guide Monitoring the Front Panel

Contents

Page VDE Class B Compliance Restricted Rights Page Contents Installing and Operating the Module Appendix a Specifications Page Figures Page Tables Page Audience How to Use This Guide Structure of This Guide Document Conventions Convention Indicates ExampleUsr/snm/agents 3Com Documents Related Documents Reference Documents Slot ONline System Concentrator Installation and OperationPage Introduction 10BASE-FB Module Descriptions Introduction 1 Theory of Operation 10BASE-FB Compliance BASE-FB Module Connections Compatibility With Other Ethernet Fiber Products BASE-FB Module Compatibility3Com Product Part Number Designing and Expanding the Network Rule Definition Recommendations/Notes Rules for Configuring a NetworkUnderstanding the General Rules Basic Network Rules Definition Recommendations/Notes Is actually equal to 1.1 meters Equivalent Fiber Distances Equivalent Fiber Distances of LAN ProductsLAN Product Equivalent Fiber Determining Maximum Fiber Link Distances Determining Link Budget Calculating Maximum Link Distance DBm ONline 10BASE-FB Module Optical Power Budget Normal PowerPower Link Link Loss ONline to ONline 10BASE-FB Module Optical Power Budget High PowerBASE-FB Optical Power Budget Cable Size Used Transmit Receive Optical Power Micron Attenuation Typical Fiber Loss Characteristics Connector and Splice Insertion Loss Meter Fiber Link With Mechanical Splice Example 1700 Meter Fiber Link With Mechanical Splice Meter Fiber Link Through Two Patch Panels Example 2000 Meter Fiber Link Through Two Patch Panels Choosing a Network Backbone Cabling Structure Star-Wiring Configuration Star Configuration Serial Configuration Using 10BASE-FB Modules Serial Configuration Fiber Backbone, Fiber-to-the-Desk 10BASE-FB Module Configurations All-Fiber Network Network With 3 Concentrators Example Network With 3 Concentrators Example Network with 8 Concentrators Network Configured With 8 Concentrators Fiber Equivalent Distances Between Transceivers Fiber Backbone, Unshielded Twisted Pair to-the-Desk Example Sample Configuration Distance Calculation Sample Configuration Distance Calculation Fiber Backbone, Coaxial Connection Example Connecting a Thin Ethernet 10BASE2 Segment Designing and Expanding the Network 2 Fault-Tolerant Configurations Configuring Ports for Fault ToleranceStandard Redundant Configuration In this configuration Setting Redundancy 10. Redundant Fiber Backbone Configuration Implementing Total Backbone Fault Tolerance 11. Total Backbone Fault-Tolerant Configuration 12. Fiber Network With 3 Concentrators Page Installing and Operating the Module Precautionary Procedures Unpacking Procedures Quick Installation Quick Installation ProceduresStep Procedure Section Title Setting the Dip Switches BASE-FB Module Dip Switch Locations Setting Dip Switch S1 Dip Switch S1 Settings for Switches 1Switch Label Function Factory Switch Setting Default Off Channel Selection Dip Switch S1 Settings for Switches 3 toPort-Switching Module Port Module-Switching Module Setting Dip Switch S2 Dip Switch S2 SettingsSwitch Label Function Factory Switch Setting Default Enable/disable Disable Module Low Light Detection Not Used Installing the Module Installing the 10BASE-FB Module BASE-FB Module Connection Configuring the Module Enabling Ports Selecting a Network Enabling Port Redundancy You can enable port redundancy in one of the following ways Enabling Low Light Warning Enabling Optical Power Saving Module Configuration Showing Module Configuration Monitoring the Front Panel Page LED Name Color State Indicates Interpreting the 10BASE-FB Module LEDs LED State Network Configuration Verifying LED and Network AssignmentsNetwork Check Codes Troubleshooting Troubleshooting Using the Port Activity LEDs Troubleshooting Using the Port Activity LEDsPossible Cause Corrective Action Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDsLED State Indication Possible Cause Corrective Action Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDs 10BASE-FL Technical Assistance Page Specifications Table A-1. General Specifications General Specifications Cable Type Normal Power High Power Optical SpecificationsTransmitter Specifications Table A-2. Transmit Power Receiver Specifications Table A-3. Receiver SpecificationsSupported Fiber Optic Cables Fiber Optic Interface Power RequirementsTable A-4. Fiber Optic Interface Specifications Table A-5. Power Requirements Table A-7. Mechanical Specifications Environmental SpecificationsMechanical Specifications Table A-6. Electrical Specifications 10BASE-FB Cables 10BASE-FB Cable and Connector Specifications 10BASE-FB Connectors Port-Switching Connector TypeTable A-8 BASE-FB Module Part Numbers On-line Technical Support Technical Support Support from Your Network Supplier Email Technical SupportWorld Wide Web Site Support from 3Com Returning Products for Repair Accessing the 3Com MIB 3Com Technical Publications Page Index Installing Link Budget Redundant Link, 3-16Redundancy LED Unpacking Procedures, 3-3Unshielded Twisted Pair Cable