Power Requirements, Fiber Optic Interface | 3Com 5104M-FB1 instruction

Fiber Optic Interface

Table A-4 lists specifications for the fiber optic interface.

Table A-4. Fiber Optic Interface Specifications

Data Rate	10 Mbps (million bits per second)

Data Modulation	Manchester

Diagnostic Modulation	Pulse Width

Fiber Optic Interface	ST-, SMA-, and FC-type

Signaling	Compatible with all 10BASE-FB
	and 10BASE-FB products

Power Requirements

Table A-5 lists power requirements for the 10BASE-FB Module.

Table A-5. Power Requirements

Power Requirements	1.7	Amp @ 5 V

Fuse	4.0	Amps for 5 V, Fast blow

Power Consumption	8.5 Watts

BTU/hour	29.0

Specifications A - 5

Image 91

3Com 5104M-FB1, 5102M-FBP, 510M-FBP Table A-4. Fiber Optic Interface Specifications, Table A-5. Power Requirements

Contents

Page VDE Class B Compliance Restricted Rights Page Contents Installing and Operating the Module Appendix a Specifications Page Figures Page Tables Page Audience How to Use This Guide Structure of This Guide Convention Indicates Example Document ConventionsUsr/snm/agents 3Com Documents Related Documents Reference Documents Slot ONline System Concentrator Installation and OperationPage Introduction 10BASE-FB Module Descriptions Introduction 1 Theory of Operation 10BASE-FB Compliance BASE-FB Module Connections BASE-FB Module Compatibility Compatibility With Other Ethernet Fiber Products3Com Product Part Number Designing and Expanding the Network Rule Definition Recommendations/Notes Rules for Configuring a NetworkUnderstanding the General Rules Basic Network Rules Definition Recommendations/Notes Is actually equal to 1.1 meters Equivalent Fiber Distances of LAN Products Equivalent Fiber DistancesLAN Product Equivalent Fiber Determining Maximum Fiber Link Distances Determining Link Budget Calculating Maximum Link Distance DBm ONline 10BASE-FB Module Optical Power Budget Normal PowerPower Link Link Loss ONline to ONline 10BASE-FB Module Optical Power Budget High PowerBASE-FB Optical Power Budget Cable Size Used Transmit Receive Optical Power Micron Attenuation Typical Fiber Loss Characteristics Connector and Splice Insertion Loss Meter Fiber Link With Mechanical Splice Example 1700 Meter Fiber Link With Mechanical Splice Meter Fiber Link Through Two Patch Panels Example 2000 Meter Fiber Link Through Two Patch Panels Choosing a Network Backbone Cabling Structure Star-Wiring Configuration Star Configuration Serial Configuration Using 10BASE-FB Modules Serial Configuration Fiber Backbone, Fiber-to-the-Desk 10BASE-FB Module Configurations All-Fiber Network Network With 3 Concentrators Example Network With 3 Concentrators Example Network with 8 Concentrators Network Configured With 8 Concentrators Fiber Equivalent Distances Between Transceivers Fiber Backbone, Unshielded Twisted Pair to-the-Desk Example Sample Configuration Distance Calculation Sample Configuration Distance Calculation Fiber Backbone, Coaxial Connection Example Connecting a Thin Ethernet 10BASE2 Segment Designing and Expanding the Network 2 Configuring Ports for Fault Tolerance Fault-Tolerant ConfigurationsStandard Redundant Configuration In this configuration Setting Redundancy 10. Redundant Fiber Backbone Configuration Implementing Total Backbone Fault Tolerance 11. Total Backbone Fault-Tolerant Configuration 12. Fiber Network With 3 Concentrators Page Installing and Operating the Module Precautionary Procedures Unpacking Procedures Quick Installation Procedures Quick InstallationStep Procedure Section Title Setting the Dip Switches BASE-FB Module Dip Switch Locations Dip Switch S1 Settings for Switches 1 Setting Dip Switch S1Switch Label Function Factory Switch Setting Default Off Channel Selection Dip Switch S1 Settings for Switches 3 toPort-Switching Module Port Module-Switching Module Dip Switch S2 Settings Setting Dip Switch S2Switch Label Function Factory Switch Setting Default Enable/disable Disable Module Low Light Detection Not Used Installing the Module Installing the 10BASE-FB Module BASE-FB Module Connection Configuring the Module Enabling Ports Selecting a Network Enabling Port Redundancy You can enable port redundancy in one of the following ways Enabling Low Light Warning Enabling Optical Power Saving Module Configuration Showing Module Configuration Monitoring the Front Panel Page LED Name Color State Indicates Interpreting the 10BASE-FB Module LEDs Verifying LED and Network Assignments LED State Network ConfigurationNetwork Check Codes Troubleshooting Troubleshooting Using the Port Activity LEDs Troubleshooting Using the Port Activity LEDsPossible Cause Corrective Action Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDsLED State Indication Possible Cause Corrective Action Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDs 10BASE-FL Technical Assistance Page Specifications Table A-1. General Specifications General Specifications Cable Type Normal Power High Power Optical SpecificationsTransmitter Specifications Table A-2. Transmit Power Table A-3. Receiver Specifications Receiver SpecificationsSupported Fiber Optic Cables Fiber Optic Interface Power RequirementsTable A-4. Fiber Optic Interface Specifications Table A-5. Power Requirements Table A-7. Mechanical Specifications Environmental SpecificationsMechanical Specifications Table A-6. Electrical Specifications 10BASE-FB Cables 10BASE-FB Cable and Connector Specifications Port-Switching Connector Type 10BASE-FB ConnectorsTable A-8 BASE-FB Module Part Numbers On-line Technical Support Technical Support Email Technical Support Support from Your Network SupplierWorld Wide Web Site Support from 3Com Returning Products for Repair Accessing the 3Com MIB 3Com Technical Publications Page Index Installing Link Budget Redundant Link, 3-16Redundancy LED Unpacking Procedures, 3-3Unshielded Twisted Pair Cable