DIP Switch SW1 Network Selection Settings | 3Com 5112M-TPLS specification

Network selection switches 1 and 2 enable you to select a channel for the module. Switches 1 and 2 are factory set to On. Therefore, the Security Module is initially configured to network 1. To reconfigure the module to a different network, refer to the information in .

Table 3-2. DIP Switch SW1 Network Selection Settings

	Switch 1	Switch 2	Network Selection

Switch Settings	On	On	1 (default)

	Off	On	2

	On	Off	3

	Off	Off	Isolated (module
			operates
			independently of the
			three backplane
			networks)

Switch 3 (Security) allows you to enable or disable Security mode and enable or disable port mode for all 12 ports on the Security Module. Switch 3 is configured to affect both Security mode and the port mode setting in order to protect your ports in the event the management module fails.

When the Security switch is set to enabled, port mode is set to disabled. Conversely, when the Security switch is set to disabled, port mode is set to enabled.

This dual purpose setting provides maximum security for all ports on the Security Module and also provides you with the flexibility of using the ports as non-secure ports in the event the management module fails. Without management, you may elect to have traffic continue to pass through the non-secure ports. However, your environment may require secure ports at all times. In this situation, you would choose to disable the ports rather than keep them enabled in a non-secure environment.

3 - 6 ONline 10BASE-T Security Module Installation and Operation Guide

Image 42

3Com 5112M-TPLS DIP Switch SW1 Network Selection Settings, Switch Network Selection Switch Settings

Contents

Page VDE Class B Compliance Restricted Rights Page Contents Installing and Operating the Module Troubleshooting Appendix B Technical Support Figures Page Tables Page How to Use This Guide Audience Structure of This Guide Document Conventions Convention Indicates ExampleUsr/snm/agents Related Documents 3Com Documents Reference DocumentsPage Introduction ONline 10BASE-T Security Module Theory of Operation Application ONline Management ONline 10BASE-T Security Module ApplicationPage Designing and Expanding the Network Understanding the General Rules Basic Network Rules Seven Basic Network Rules Rule Definition Recommendations/Notes Certain LAN devices Seven Basic Network Rules LAN Equivalence LAN Product Equivalent DistancesLAN Product Equivalent Fiber Fiber Backbone, Twisted Pair To-The-Desk Fiber Backbone, Twisted Pair To-The-Desk Example Sample Configuration Distance Calculation Twisted Pair Backbone, Twisted Pair To-The-Desk Maximum Link Distance on Twisted PairCable Gauge Supports Link Distances Up To Patch Panels Unshielded Twisted Pair Network Redundant Twisted Pair Configuration Redundant Links Designing and Expanding the Network 2 Page Installing and Operating the Module Procedures for Completing Installation Precautionary ProceduresQuick Installation Chart Step Procedure Reference Installing the Module Unpacking Procedures Setting the Dip Switch Security Module Dip Switch SW1 Location DIP Switch SW1 Network Selection Settings Switch Network Selection Switch Settings DIP Switch SW1 Security and Link Integrity Settings Switch Function Factory SettingOff On Installing the Module Installing the Cable Tie-Wrap Kit Attaching the Tie-Wrap Bracket to the Module Attaching Cables With 90 Connectors Installing the Module Installing an ONline 10BASE-T Security Module ONline 10BASE-T Security Module Cable Connection Configuring the Module Port Enable Network AssignmentPort Redundancy Link Integrity Module Security Saving Module Configurations Reverting Module ConfigurationsAutopartition Threshold Showing Module Configurations Show Module Show Module Verbose Show Port Show Port Verbose Monitoring the Front Panel Security Module Faceplate Interpretation of the Security Module LEDs Color State Indicates Name LED State Network Configuration LED and Network VerificationNetwork Check Codes Page Configuring Security Features Quick Reference for Configuring Security Quick Reference for Configuring the Security ModuleProcedure Command SET Security Autolearn Configuring Security Features Eavesdropping Security Intrusion Detection Example of Eavesdropping Security Defining Port Security Type Example of Intrusion Detection Defining Port Action on Intrusion Configuring Autolearning Mask Enabling Ports Configuring Autolearning Autolearn capture done learned 0 addresses total Defining a MAC Address Manually Downloading the Autolearning Database Configuring Security Mode Showing Security Configurations Saving Security ConfigurationsReverting Security Configurations Showing Port Configurations Eavesdrop None ETHERNET1 Showing Security Autolearn Showing Security Intruder List Clearing Security Configurations Clearing the MAC Address Table Clearing the Autolearning Database Clearing the Security Intruder List Using 3Com MIB Security Variables EMM Security Snmp Variables Using the Security Module Snmp Variables Configuring Security Features 4 Page Troubleshooting Troubleshooting Troubleshooting Using the Status LEDs Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDs Troubleshooting Using the Activity LEDs Troubleshooting Using the Activity LEDsLED State Possible Problem Troubleshooting Solutions Technical Assistance Page Specifications Electrical Specifications Environmental Specifications Mechanical SpecificationsGeneral Specifications Pin Connector and Cable Figure A-1 -Pin Cable Male and Female Connectors Port # Function Table A-1 -Pin Cable Pinouts and Port AssignmentsHub Trans Ceiver Polarity Hub Twisted Pair Connectors and CablesHub Trans Port # Twisted Pair Connectors Figure A-2. RJ-45 Connector Pinouts Twisted Pair Cables Technical Support On-line Technical Support Support from Your Network Supplier Email Technical SupportWorld Wide Web Site Support from 3Com Accessing the 3Com MIB Returning Products for Repair 3Com Technical Publications Page Index Activity LEDs, 3-18,3-20 Quick Reference Chart Security Type Default Setting Index