Appendix B Current Status Messages | ADTRAN ISU 2X64 guide

Appendix B

Current Status Messages

This appendix lists the status line messages and their definitions. Messages shown entirely in capital letters are generated by the ISDN network. Messages with lower case letters are generated by the ISU 2x64.

AT&T-5ESS Ready

The ISU is connected to an AT&T-5ESS switch and is ready to place/receive calls.

Call Connect B1

Bearer channel 1 is connected and is active.

Call Connect B2

Bearer channel 2 is connected and is active.

CALL xxxxxxx

The ISU is calling phone number xxxxxxx.

DEACTIVATED

The network interface is not active.

DISCONNECTED

The network has activated layer 1 but layer 2 is inactive. To acti- vate the unit a setup message must be sent or received.

DISCONNECTING

The current phone call is being disconnected (hung up).

61200051L1-1D

ISU 2x64 Dual Port ISDN Service Unit User Manual

95

Image 109

ADTRAN ISU 2X64 user manual Appendix B Current Status Messages

Contents

Part Numbers ISU Dual Port Isdn Service Unit Trademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version DSU 57.6 Async Txinit Txfa TXADD01 Txdeq Tanull TcidSAP Fallback 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Adtran ISU Isdn Overview ISU 2x64 Rear Panel Indicator Deﬁnition DTE Indicators ISU 2X64 Single Port Operation ISU 2X64 InteroperabilityISU 2x64 Front Panel ISU 2x64 Interoperability DTE#2 Recommended Operating Protocols Call Type Protocol Sync Rates Supported bps Async Recommended Operating Modes Understanding Isdn and the ISU Isdn Ordering Codes Chapter Isdn Service Capability R previously Generic Data Capability S previously Generic Data M Capability C previously Generic Data C B1 previously Generic Data BI2 previously Generic Data I-1DN J3 previously Generic Data J-1DN M5 previously Generic Data M-1DN J2 previously Generic Data J Network Connection Chapter Installation DTE Data Connection VT 100 Maintenance Help Screen Maintenance Interface Dial Interface Connection Menu Navigation Chapter Operation Current Status Menu Front Panel DTE Indicators Getting Started VT 100 Menu Support Status Buffer VT 100 Status Screen Status Screen VT 100 Configuration Screen Configuration Screen Test Options Chapter TestingVT 100 Test Menu Screen Loopback Network Loopback DTELoopback Protocol Test Menu Tree Loopback Remote Loopback DisableTest Remote Software Version NEBE/FEBELoopback Both DTEs Test 2047 Both Dial Line Operation Chapter ConfigurationDial Line Menu Tree VT 100 Configuration Menu Screen Setting the Switch Protocol =AT&T 5ESS LCD Configuration Menu Tree Cofiguration Setting the Call Type Smart Dial Strings Setting the Terminal ID Setting the Busy Out Port Setting the Dial Options Dial Options, RS-366 Menu Tree =CONFIG AT Commands Example ATI1 Example ATSS80? =V.25 Dial Options, V.25 bis Menu Tree Dial Line, Auto Answer Menu Tree =CONFIG Bis Async Menu Tree Data Bits Menu Tree Setting Auto Answer Setting Answer Tone =Dial Line =Netw. options Answer Tone Menu Tree Setting Call Screening Setting Connect TimoutConnect Timout Menu Tree Call Screening Menu Tree SBus Termination Menu Tree SBus Termination Clock mode Slave/Master Leased Line ServiceLeased Line Menu Tree Limited Distance Modem Applications Channel RateLeased Application with Channel Banks SBus Termination Asynchronous DTE Options Menu Tree DTE Options for Asynchronous and Synchronous OperationSynchronous DTE Options Menu Tree Bit Rate DTR Options Data Format Menu Tree Flow Control Menu Tree Transmit Clock Menu Tree Autobaud Protocol Menu Tree Setting Protocol Options Clear Channel =BONDING mode Protocol BONDING, Mode 1 Menu Tree Txdeq DSU 57.6 Async Call Type Rate Adaption Protocols Typical Units Supported Rate Adaptation Protocols PPP Menu Tree Point-to-Point Protocol PPP Front Panel Dialing Options Chapter Dial OptionsVT 100 Dial Options Screen Dial Menu Tree Dial number Hang up lineRedial last # Answer Call Quick Setup Configuration Chapter Quick SetupQuick Setup Menu Tree Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line Second AT&T 5ESS Quick Setup Security Menu Tree Security Remote Config Set PasswordRemote Config Menu Tree Lock Keypad Lpbk remote 1B Cfg. Rmt. UnitLpbk remote 2B Security and Remote Configuration If Self Test Fails Chapter TroubleshootingIf The ISU 2x64 Does Not Read Ready Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call If you Cannot Connect Calls Troubleshooting Calls Chapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications Appendix a AT Commands Carrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Register List Appendix DAuto Answer Character Is set Number S26.......DTE Rate AdjustLOW Layer Comp = Locd DTE CDDTE DTR DTR = Bisync = NEC S52.......SWITCH Type Type Dial Mode= Fallback = PPP Channel Rate DTE ModeSPID1 LOC SPID2 LOC DTE DTE FlowDCE DTE Clock 118 EIA-232 Interface Appendix E Interface RS-530 ST-B RS-366 Interface PIN RJ-45 Dial Line Connector U Interface Maintenance Connector RJ-45 Dial Line Connector S/T Interface 124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Local Interface Requirements Local ServicePhysical Interface Deciding What Services to Order Long Distance Service5ESS Custom Line Additional Parameters 5ESS Features DMS-100 Protocol Version 1 Line Additional Parameters DMS Features Setting UP the ISU 2X64 for a NEW Line After Service Is Installed 134 Acronyms PRI Asynchronous transmission Glossary Ccitt DDS Isdn NT1 TE1 2B+D 144 Numerics Index 146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information