Understanding Isdn and the ISU | ADTRAN ISU 2X64 specification

Chapter 1.Understanding ISDN and the ISU 2x64

1.All asynchronous rates support flow control.

2.All dial-up modes support front panel, DTR, RS-366, AT command, and V.25 dialing methods.

3. Rates marked with f require flow control.

4. Given a choice between two protocols, pick the protocol closer to the top of the list.

5.Rate marked with v is available on Port 2 only.

8

ISU 2x64 Dual Port ISDN Service Unit User Manual

61200051L1-1D

Image 22

ADTRAN ISU 2X64 user manual Understanding Isdn and the ISU

Contents

ISU Dual Port Isdn Service Unit Part Numbers Trademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version DSU 57.6 Async Txinit Txfa TXADD01 Txdeq Tanull TcidSAP Fallback 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Isdn Overview Adtran ISU ISU 2x64 Rear Panel DTE Indicators Indicator Deﬁnition ISU 2X64 Single Port Operation ISU 2X64 InteroperabilityISU 2x64 Front Panel ISU 2x64 Interoperability Recommended Operating Protocols DTE#2 Recommended Operating Modes Call Type Protocol Sync Rates Supported bps Async Understanding Isdn and the ISU Chapter Isdn Service Isdn Ordering Codes Capability S previously Generic Data M Capability R previously Generic Data I2 previously Generic Data I-1DN B1 previously Generic Data BCapability C previously Generic Data C J3 previously Generic Data J-1DN J2 previously Generic Data J M5 previously Generic Data M-1DN Chapter Installation Network Connection DTE Data Connection Maintenance Interface VT 100 Maintenance Help Screen Dial Interface Connection Chapter Operation Menu Navigation Front Panel DTE Indicators Current Status Menu VT 100 Menu Support Getting Started Status Buffer Status Screen VT 100 Status Screen Configuration Screen VT 100 Configuration Screen Test Options Chapter TestingVT 100 Test Menu Screen Loopback Protocol Loopback DTELoopback Network Test Menu Tree Loopback Remote Loopback DisableTest Remote Loopback Both DTEs NEBE/FEBESoftware Version Test 2047 Both Dial Line Operation Chapter ConfigurationDial Line Menu Tree Setting the Switch Protocol VT 100 Configuration Menu Screen LCD Configuration Menu Tree =AT&T 5ESS Cofiguration Setting the Call Type Setting the Terminal ID Smart Dial Strings Setting the Busy Out Port Setting the Dial Options =CONFIG Dial Options, RS-366 Menu Tree AT Commands Example ATI1 Example ATSS80? Dial Options, V.25 bis Menu Tree =V.25 =CONFIG Dial Line, Auto Answer Menu Tree Data Bits Menu Tree Bis Async Menu Tree Setting Auto Answer Setting Answer Tone Answer Tone Menu Tree =Dial Line =Netw. options Connect Timout Menu Tree Setting Connect TimoutSetting Call Screening Call Screening Menu Tree SBus Termination SBus Termination Menu Tree Clock mode Slave/Master Leased Line ServiceLeased Line Menu Tree Limited Distance Modem Applications Channel RateLeased Application with Channel Banks SBus Termination Asynchronous DTE Options Menu Tree DTE Options for Asynchronous and Synchronous OperationSynchronous DTE Options Menu Tree Bit Rate DTR Options Flow Control Menu Tree Data Format Menu Tree Autobaud Transmit Clock Menu Tree Setting Protocol Options Protocol Menu Tree Clear Channel Protocol BONDING, Mode 1 Menu Tree =BONDING mode Txdeq DSU 57.6 Async Rate Adaptation Protocols Call Type Rate Adaption Protocols Typical Units Supported PPP Menu Tree Point-to-Point Protocol PPP VT 100 Dial Options Screen Chapter Dial OptionsFront Panel Dialing Options Dial Menu Tree Redial last # Hang up lineDial number Answer Call Quick Setup Configuration Chapter Quick SetupQuick Setup Menu Tree Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line AT&T 5ESS Second Quick Setup Security Security Menu Tree Remote Config Menu Tree Set PasswordRemote Config Lock Keypad Lpbk remote 1B Cfg. Rmt. UnitLpbk remote 2B Security and Remote Configuration If Self Test Fails Chapter TroubleshootingIf The ISU 2x64 Does Not Read Ready Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call Troubleshooting Calls If you Cannot Connect Calls Chapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications AT Commands Appendix a Carrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Auto Answer Appendix DRegister List Character Is set Number S26.......DTE Rate AdjustLOW Layer Comp DTE DTR DTE CD= Locd DTR = Bisync S52.......SWITCH Type = NEC = Fallback Dial ModeType = PPP SPID1 LOC DTE ModeChannel Rate SPID2 LOC DCE DTE FlowDTE DTE Clock 118 Appendix E EIA-232 Interface RS-530 Interface RS-366 Interface ST-B RJ-45 Dial Line Connector U Interface PIN RJ-45 Dial Line Connector S/T Interface Maintenance Connector 124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Local Interface Requirements Local ServicePhysical Interface Deciding What Services to Order Long Distance Service5ESS Custom Line Additional Parameters 5ESS Features DMS Features DMS-100 Protocol Version 1 Line Additional Parameters After Service Is Installed Setting UP the ISU 2X64 for a NEW Line 134 Acronyms PRI Glossary Asynchronous transmission Ccitt DDS Isdn NT1 TE1 2B+D 144 Index Numerics 146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information