ADTRAN ISU 2X64 user manual LCD Configuration Menu Tree, =AT&T 5ESS

Chapter 6. Configuration

STATUS	‘Buffer Display’
	<Use Up and Down keys to Scroll>

	1=AT&T 5ESS
	2= DMS-100
	3=National ISDN1
	4=NEC Switch
1=Switch Protocl	5=TDX10*	*Only available on part number
	6=TDX1B*	1200051L5 and 1200051L6.
	7=EuroISDN*
	8=VN4*
	9=KDD*
	10=NTT*
2=Call type	dte#1	1=Speech
	dte#2	2=Audio
		3=Data 56Kbps
		4=Data 64Kbps
		1=1 sec or EON

KEY

dte#1

dte#2

This symbol means the menu items that follow can

be configured for DTE#1 or DTE#2 when entering these portions of the menu tree. Use the up and down ARROW keys to choose DTE#1 or DTE#2.

Press ENTER to select.

Use the CANCEL key to back up.

TEST dte#1

dte#2

1=Loopback DTE
2=Loopback Netw.
3=Loopback Proto
4=Loopback Remot
5=Test Remote
6=Lpbk Disable	1=No Rem Lpbks
7=NEBE/FEBE	2=DDS Accepted
8=Software Ver	3=V54 Accepted
9=Lpbk Both DTE	4=DDS + V54 Accept
0=Test 2047 Both

3=Terminal ID	Set SPID	dte#1 <SPID>	2=2 sec or EON
			3=5 sec (default)
	Set LDN dte#1 <LDN>	dte#2 <SPID>	4=10 sec or EON
	dte#2 <LDN>		5=20 sec or EON
			6=Wait for EON
4=Busy Out	1=Enabled	1=Front Panel		1=V.25 HDLC
	2=Disabled
				2=V.25 ASYNC
		2=RS-366
5=Dial options	dte#1	3=AT commands		3=V.25 BISYNC
		4=V.25		4=V.25 HDLC FLAG
	dte#2
		5=Disabled
6=Auto answer	dte#1	1=Disabled
	dte#2	2=Enabled
		3=Dump all calls
7=Answer tone	dte#1	1=No answer tone
	dte#2	2=Incoming tone
		3=Outgoing tone
8=Connect Timout	1=15 sec	4=Always tone
	2=30 sec (def)
	3=1 minute

NOTE: Bold type represents default.

1=Bit Rate	1=300	6=19200
	2=1200	7=38400
	3=2400	8=57600
	4=4800	9=115200
	5=9600

1=Netw. options	1=Dial Line
	2=Leased Line

CONFIG

	4=2 minute
	5=4 minute
9=Call Screening	1=Answer any	1=Clock mode	1=Slave
	2=Ansr if SNO…9
			2=Master
			1=64k
10=SBUS Terminati	1=100 ohm On	2=Channel rate
			2=128k
	2=100 ohm Off
		3=SBus Terminati	1=100 ohm On

2=Connector Type	1=RS-530
	2=V.35
	3=RS-232
3=RTS Options	1=1 ms delay
	2=18 ms delay
4=CTS Options	1=Forced CTS
	2=Follows RTS

2=100 ohm Off

5=CD Options

1= CD Forced on

2=Normal

2=DTE options	dte#1
	dte#2

3=Protocol dte#1 dte#2

1=Asynchronous

2=Synchronous

1=Clear Channel	1=TXINIT
	2=TXFA
2=BONDING mode 1
	3=TXADD01
3=V.120	4=TXDEQ
4=V.110
	5=TANULL

1=Bit Rate	1=2400	6=48000
	2=4800	7=56000
	3=9600	8=64000
	4=19200	9=112000
	5=38400	0=128000
2=Connector Type	1=RS-530
	2=V.35

6=DTR Options

3=Off with LOCD 4=Off Link Down

1=Ignore DTR 2=Cmd when Off 3=Idle when Off 4=Off>On dial #0 5=Dial #0 if On 6=Answer if On

4=Quick setup	dte#1
	dte#2

1=Dial 56K sync

2=Dial 64Ksync

3=Dial 112K sync

4=Dial 128K sync

5=Dial 57.6 asyn

6=Dial 115.2 asy

7=Fallback 57.6k

8=Leased 64K

9=Ldm 64K Master

5=DSU 57.6 ASYNC	6=TCID
6=T-LINK
	7=Async Rev
7=SAP
	1=PPP
8=FALLBACK
9=PPP asyn-sync	2=Multilink PPP
	3=PPP w/Comp

	3=RS-232
3=RTS Options	1=1 ms delay
	2=18 ms delay
4=CTS Options	1=Forced CTS
	2=Follows RTS
5=CD Options	1=CD Forced on
	2=Normal
	3=Off with LOCD
	4=Off Link Down
6=DTR Options	1=Ignore DTR
	2=Cmd when Off
	3=Idle when Off
	4=Off>On dial #0

7=DSR Options

8=Flow Control

9=Data Format

1=DSR forced on 2=OFF Idle+Test 3=OFF Link Down

1=Hardware Flow 2=Software Flow

3=No Flow Ctrl

1=Data Bits	1=8 Data bits
	2=7 Data bits
2=Parity Bits	1=None
	2=Odd
	3=Even
3=Stop Bits	1=1 Stop bit
	2=1.5 Stop bits

	5=Security	1=Set Password	Password < >
	6=Remote Config	2=Lock Keypad	Password Required
	dte#1	1=Hang up line
DIAL
	dte#2	2=Dial number
		3=Redial last #
		4=Answer Call

			1=Number < >
dte#1	1=Cfg. Rmt. Unit		2=Password < >
dte#2	2=Set Password	Password < >
	3=Lpbk remote 1B	Number < >
	4=Lpbk remote 2B	Number < >

	5=Dial #0 if On
	6=Answer if On
7=DSR Options	1=DSR forced on
	2=OFF Idle+Test
	3=OFF Link Down
8=Transmit Clock	1=Normal
	2=External

3=2 Stop bits

5=Dial Stored #

6=Store/Review #

Figure 6-3

LCD Configuration Menu Tree

D ISU 2x64 Dual Port ISDN Service Unit User Manual 29