ADTRAN ISU 2X64 specification

Appendix C: Status Buffer Messages

FACILITY_REJECTED

A facility requested cannot be provided by the network.

FACILITY_NOT_SUBSCRIBED

The channel type requested has not been subscribed.

FALLBACK ERROR

Attempt to fallback to normal mode failed.

FBW disconnect

BONDING negotiation has failed due to a disconnect on a B- Channel.

FlowCtl mismatch

Bonding negotiation determined a flow control mismatch.

FlowCtl required

Bonding negotiation determined that flow control needs to be op- tioned on.

Hangup1/2

The call on either the first or second channel was disconnected by the ISU 2x64. The far-end phone number is also displayed.

InCmptblFound

TLINK end-to-end negotiations found an optioning incompatibil- ity between the two end units.

INCOMMING_CALL_BARRED

The network will not allow an incoming call.

INCOMPATIBLE_DEST

The called number cannot accept the type of call that has been placed.

INTRWORKING_UNSPEC

A message was sent by a far-end network that was not under- stood.

INVALID_CALL_REF

Call control error.

61200051L1-1D

ISU 2x64 Dual Port ISDN Service Unit User Manual

103

Image 117

ADTRAN ISU 2X64 user manual Facility requested cannot be provided by the network

Contents

Part Numbers ISU Dual Port Isdn Service Unit Trademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version Txinit Txfa TXADD01 Txdeq Tanull Tcid DSU 57.6 AsyncSAP Fallback 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Adtran ISU Isdn Overview ISU 2x64 Rear Panel Indicator Deﬁnition DTE Indicators ISU 2X64 Interoperability ISU 2X64 Single Port OperationISU 2x64 Front Panel ISU 2x64 Interoperability DTE#2 Recommended Operating Protocols Call Type Protocol Sync Rates Supported bps Async Recommended Operating Modes Understanding Isdn and the ISU Isdn Ordering Codes Chapter Isdn Service Capability R previously Generic Data Capability S previously Generic Data M Capability C previously Generic Data C B1 previously Generic Data BI2 previously Generic Data I-1DN J3 previously Generic Data J-1DN M5 previously Generic Data M-1DN J2 previously Generic Data J Network Connection Chapter Installation DTE Data Connection VT 100 Maintenance Help Screen Maintenance Interface Dial Interface Connection Menu Navigation Chapter Operation Current Status Menu Front Panel DTE Indicators Getting Started VT 100 Menu Support Status Buffer VT 100 Status Screen Status Screen VT 100 Configuration Screen Configuration Screen Chapter Testing Test OptionsVT 100 Test Menu Screen Loopback Network Loopback DTELoopback Protocol Test Menu Tree Loopback Disable Loopback RemoteTest Remote Software Version NEBE/FEBELoopback Both DTEs Test 2047 Both Chapter Configuration Dial Line OperationDial Line Menu Tree VT 100 Configuration Menu Screen Setting the Switch Protocol =AT&T 5ESS LCD Configuration Menu Tree Cofiguration Setting the Call Type Smart Dial Strings Setting the Terminal ID Setting the Busy Out Port Setting the Dial Options Dial Options, RS-366 Menu Tree =CONFIG AT Commands Example ATI1 Example ATSS80? =V.25 Dial Options, V.25 bis Menu Tree Dial Line, Auto Answer Menu Tree =CONFIG Bis Async Menu Tree Data Bits Menu Tree Setting Auto Answer Setting Answer Tone =Dial Line =Netw. options Answer Tone Menu Tree Setting Call Screening Setting Connect TimoutConnect Timout Menu Tree Call Screening Menu Tree SBus Termination Menu Tree SBus Termination Leased Line Service Clock mode Slave/MasterLeased Line Menu Tree Channel Rate Limited Distance Modem ApplicationsLeased Application with Channel Banks SBus Termination DTE Options for Asynchronous and Synchronous Operation Asynchronous DTE Options Menu TreeSynchronous DTE Options Menu Tree Bit Rate DTR Options Data Format Menu Tree Flow Control Menu Tree Transmit Clock Menu Tree Autobaud Protocol Menu Tree Setting Protocol Options Clear Channel =BONDING mode Protocol BONDING, Mode 1 Menu Tree Txdeq DSU 57.6 Async Call Type Rate Adaption Protocols Typical Units Supported Rate Adaptation Protocols PPP Menu Tree Point-to-Point Protocol PPP Front Panel Dialing Options Chapter Dial OptionsVT 100 Dial Options Screen Dial Menu Tree Dial number Hang up lineRedial last # Answer Call Chapter Quick Setup Quick Setup ConfigurationQuick Setup Menu Tree Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line Second AT&T 5ESS Quick Setup Security Menu Tree Security Remote Config Set PasswordRemote Config Menu Tree Lock Keypad Cfg. Rmt. Unit Lpbk remote 1BLpbk remote 2B Security and Remote Configuration Chapter Troubleshooting If Self Test FailsIf The ISU 2x64 Does Not Read Ready Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call If you Cannot Connect Calls Troubleshooting Calls Chapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications Appendix a AT Commands Carrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Register List Appendix DAuto Answer Character Is set S26.......DTE Rate Adjust NumberLOW Layer Comp = Locd DTE CDDTE DTR DTR = Bisync = NEC S52.......SWITCH Type Type Dial Mode= Fallback = PPP Channel Rate DTE ModeSPID1 LOC SPID2 LOC DTE DTE FlowDCE DTE Clock 118 EIA-232 Interface Appendix E Interface RS-530 ST-B RS-366 Interface PIN RJ-45 Dial Line Connector U Interface Maintenance Connector RJ-45 Dial Line Connector S/T Interface 124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Local Service Local Interface RequirementsPhysical Interface Long Distance Service Deciding What Services to Order5ESS Custom Line Additional Parameters 5ESS Features DMS-100 Protocol Version 1 Line Additional Parameters DMS Features Setting UP the ISU 2X64 for a NEW Line After Service Is Installed 134 Acronyms PRI Asynchronous transmission Glossary Ccitt DDS Isdn NT1 TE1 2B+D 144 Numerics Index 146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information