Trademarks | ADTRAN ISU 2X64 specification

Trademarks:

Ascend is a registered trademark of Ascend Communications, Inc. ISU is a trademark of ADTRAN, Incorporated.

Macintosh is a registered trademark of Apple Computer, Inc. Teleos is a registered trademark of Teleos Communications, Inc. Windows is a registered trademark of Microsoft corporation. 5ESS is a registered trademark of AT&T.

DMS-100 is a trademark of Northern Telecom.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

© 1998 ADTRAN, Inc.

All rights reserved.

Printed in USA.

Image 2

ADTRAN ISU 2X64 user manual Trademarks

Contents

ISU Dual Port Isdn Service Unit Part Numbers Trademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version SAP Fallback Txinit Txfa TXADD01 Txdeq Tanull TcidDSU 57.6 Async 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Isdn Overview Adtran ISU ISU 2x64 Rear Panel DTE Indicators Indicator Deﬁnition ISU 2x64 Front Panel ISU 2X64 InteroperabilityISU 2X64 Single Port Operation ISU 2x64 Interoperability Recommended Operating Protocols DTE#2 Recommended Operating Modes Call Type Protocol Sync Rates Supported bps Async Understanding Isdn and the ISU Chapter Isdn Service Isdn Ordering Codes Capability S previously Generic Data M Capability R previously Generic Data I2 previously Generic Data I-1DN B1 previously Generic Data BCapability C previously Generic Data C J3 previously Generic Data J-1DN J2 previously Generic Data J M5 previously Generic Data M-1DN Chapter Installation Network Connection DTE Data Connection Maintenance Interface VT 100 Maintenance Help Screen Dial Interface Connection Chapter Operation Menu Navigation Front Panel DTE Indicators Current Status Menu VT 100 Menu Support Getting Started Status Buffer Status Screen VT 100 Status Screen Configuration Screen VT 100 Configuration Screen VT 100 Test Menu Screen Chapter TestingTest Options Loopback Protocol Loopback DTELoopback Network Test Menu Tree Test Remote Loopback DisableLoopback Remote Loopback Both DTEs NEBE/FEBESoftware Version Test 2047 Both Dial Line Menu Tree Chapter ConfigurationDial Line Operation Setting the Switch Protocol VT 100 Configuration Menu Screen LCD Configuration Menu Tree =AT&T 5ESS Cofiguration Setting the Call Type Setting the Terminal ID Smart Dial Strings Setting the Busy Out Port Setting the Dial Options =CONFIG Dial Options, RS-366 Menu Tree AT Commands Example ATI1 Example ATSS80? Dial Options, V.25 bis Menu Tree =V.25 =CONFIG Dial Line, Auto Answer Menu Tree Data Bits Menu Tree Bis Async Menu Tree Setting Auto Answer Setting Answer Tone Answer Tone Menu Tree =Dial Line =Netw. options Connect Timout Menu Tree Setting Connect TimoutSetting Call Screening Call Screening Menu Tree SBus Termination SBus Termination Menu Tree Leased Line Menu Tree Leased Line ServiceClock mode Slave/Master Leased Application with Channel Banks Channel RateLimited Distance Modem Applications SBus Termination Synchronous DTE Options Menu Tree DTE Options for Asynchronous and Synchronous OperationAsynchronous DTE Options Menu Tree Bit Rate DTR Options Flow Control Menu Tree Data Format Menu Tree Autobaud Transmit Clock Menu Tree Setting Protocol Options Protocol Menu Tree Clear Channel Protocol BONDING, Mode 1 Menu Tree =BONDING mode Txdeq DSU 57.6 Async Rate Adaptation Protocols Call Type Rate Adaption Protocols Typical Units Supported PPP Menu Tree Point-to-Point Protocol PPP VT 100 Dial Options Screen Chapter Dial OptionsFront Panel Dialing Options Dial Menu Tree Redial last # Hang up lineDial number Answer Call Quick Setup Menu Tree Chapter Quick SetupQuick Setup Configuration Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line AT&T 5ESS Second Quick Setup Security Security Menu Tree Remote Config Menu Tree Set PasswordRemote Config Lock Keypad Lpbk remote 2B Cfg. Rmt. UnitLpbk remote 1B Security and Remote Configuration If The ISU 2x64 Does Not Read Ready Chapter TroubleshootingIf Self Test Fails Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call Troubleshooting Calls If you Cannot Connect Calls Chapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications AT Commands Appendix a Carrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Auto Answer Appendix DRegister List Character Is set LOW Layer Comp S26.......DTE Rate AdjustNumber DTE DTR DTE CD= Locd DTR = Bisync S52.......SWITCH Type = NEC = Fallback Dial ModeType = PPP SPID1 LOC DTE ModeChannel Rate SPID2 LOC DCE DTE FlowDTE DTE Clock 118 Appendix E EIA-232 Interface RS-530 Interface RS-366 Interface ST-B RJ-45 Dial Line Connector U Interface PIN RJ-45 Dial Line Connector S/T Interface Maintenance Connector 124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Physical Interface Local ServiceLocal Interface Requirements 5ESS Custom Line Additional Parameters Long Distance ServiceDeciding What Services to Order 5ESS Features DMS Features DMS-100 Protocol Version 1 Line Additional Parameters After Service Is Installed Setting UP the ISU 2X64 for a NEW Line 134 Acronyms PRI Glossary Asynchronous transmission Ccitt DDS Isdn NT1 TE1 2B+D 144 Index Numerics 146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information