VT 100 Configuration Screen | ADTRAN ISU 2X64 instruction

Chapter 4.Operation

Configuration Screen

Once the unit is selected using the terminal interface, the display shows the Conﬁguration Menu (see Figure 4-3). This screen shows the current conﬁguration, line, and call status for the selected unit. See Conﬁguration on page 27 for more information about conﬁguring the ISU 2x64.

Figure 4-3

VT 100 Configuration Screen

To quickly and easily conﬁgure the ISU 2x64 for most applica- tions, see Quick Setup on page 65.

22

ISU 2x64 Dual Port ISDN Service Unit User Manual

61200051L1-1D

Image 36

ADTRAN ISU 2X64 user manual VT 100 Configuration Screen

Contents

ISU Dual Port Isdn Service Unit Part Numbers Trademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version Txinit Txfa TXADD01 Txdeq Tanull Tcid DSU 57.6 AsyncSAP Fallback 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Isdn Overview Adtran ISU ISU 2x64 Rear Panel DTE Indicators Indicator Deﬁnition ISU 2X64 Interoperability ISU 2X64 Single Port OperationISU 2x64 Front Panel ISU 2x64 Interoperability Recommended Operating Protocols DTE#2 Recommended Operating Modes Call Type Protocol Sync Rates Supported bps Async Understanding Isdn and the ISU Chapter Isdn Service Isdn Ordering Codes Capability S previously Generic Data M Capability R previously Generic Data B1 previously Generic Data B Capability C previously Generic Data CI2 previously Generic Data I-1DN J3 previously Generic Data J-1DN J2 previously Generic Data J M5 previously Generic Data M-1DN Chapter Installation Network Connection DTE Data Connection Maintenance Interface VT 100 Maintenance Help Screen Dial Interface Connection Chapter Operation Menu Navigation Front Panel DTE Indicators Current Status Menu VT 100 Menu Support Getting Started Status Buffer Status Screen VT 100 Status Screen Configuration Screen VT 100 Configuration Screen Chapter Testing Test OptionsVT 100 Test Menu Screen Loopback DTE Loopback NetworkLoopback Protocol Test Menu Tree Loopback Disable Loopback RemoteTest Remote NEBE/FEBE Software VersionLoopback Both DTEs Test 2047 Both Chapter Configuration Dial Line OperationDial Line Menu Tree Setting the Switch Protocol VT 100 Configuration Menu Screen LCD Configuration Menu Tree =AT&T 5ESS Cofiguration Setting the Call Type Setting the Terminal ID Smart Dial Strings Setting the Busy Out Port Setting the Dial Options =CONFIG Dial Options, RS-366 Menu Tree AT Commands Example ATI1 Example ATSS80? Dial Options, V.25 bis Menu Tree =V.25 =CONFIG Dial Line, Auto Answer Menu Tree Data Bits Menu Tree Bis Async Menu Tree Setting Auto Answer Setting Answer Tone Answer Tone Menu Tree =Dial Line =Netw. options Setting Connect Timout Setting Call ScreeningConnect Timout Menu Tree Call Screening Menu Tree SBus Termination SBus Termination Menu Tree Leased Line Service Clock mode Slave/MasterLeased Line Menu Tree Channel Rate Limited Distance Modem ApplicationsLeased Application with Channel Banks SBus Termination DTE Options for Asynchronous and Synchronous Operation Asynchronous DTE Options Menu TreeSynchronous DTE Options Menu Tree Bit Rate DTR Options Flow Control Menu Tree Data Format Menu Tree Autobaud Transmit Clock Menu Tree Setting Protocol Options Protocol Menu Tree Clear Channel Protocol BONDING, Mode 1 Menu Tree =BONDING mode Txdeq DSU 57.6 Async Rate Adaptation Protocols Call Type Rate Adaption Protocols Typical Units Supported PPP Menu Tree Point-to-Point Protocol PPP Chapter Dial Options Front Panel Dialing OptionsVT 100 Dial Options Screen Dial Menu Tree Hang up line Dial numberRedial last # Answer Call Chapter Quick Setup Quick Setup ConfigurationQuick Setup Menu Tree Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line AT&T 5ESS Second Quick Setup Security Security Menu Tree Set Password Remote ConfigRemote Config Menu Tree Lock Keypad Cfg. Rmt. Unit Lpbk remote 1BLpbk remote 2B Security and Remote Configuration Chapter Troubleshooting If Self Test FailsIf The ISU 2x64 Does Not Read Ready Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call Troubleshooting Calls If you Cannot Connect Calls Chapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications AT Commands Appendix a Carrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Appendix D Register ListAuto Answer Character Is set S26.......DTE Rate Adjust NumberLOW Layer Comp DTE CD = LocdDTE DTR DTR = Bisync S52.......SWITCH Type = NEC Dial Mode Type= Fallback = PPP DTE Mode Channel RateSPID1 LOC SPID2 LOC DTE Flow DTEDCE DTE Clock 118 Appendix E EIA-232 Interface RS-530 Interface RS-366 Interface ST-B RJ-45 Dial Line Connector U Interface PIN RJ-45 Dial Line Connector S/T Interface Maintenance Connector 124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Local Service Local Interface RequirementsPhysical Interface Long Distance Service Deciding What Services to Order5ESS Custom Line Additional Parameters 5ESS Features DMS Features DMS-100 Protocol Version 1 Line Additional Parameters After Service Is Installed Setting UP the ISU 2X64 for a NEW Line 134 Acronyms PRI Glossary Asynchronous transmission Ccitt DDS Isdn NT1 TE1 2B+D 144 Index Numerics 146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information