Manuals
/
Agilent Technologies
/
Lawn and Garden
/
Portable Generator
Agilent Technologies
manual
Affix Label Here Part No. E4400-90333
Models:
E4400-90333
1
1
72
72
Download
72 pages
43.69 Kb
1
2
3
4
5
6
7
8
Error messages
No Error
Sales or service office
Page 1
Image 1
Error Messages
Agilent Technologies
ESG Family Signal Generators
Serial Number Prefixes:
(Affix Label Here)
Part No.
E4400-90333
Printed in USA
June 2001
Supersedes February 2001
© Copyright
1999-2001
Agilent Technologies
Page 1
Page 2
Page 1
Image 1
Page 1
Page 2
Contents
Supersedes February Copyright 1999-2001 Agilent Technologies
Affix Label Here Part No. E4400-90333
Contents
Introduction
Error Message Format
Error Message Types
No Error
To -400 Query Errors
Device has detected a failure during its self-test procedure
To -300 Device-Specific Errors
Self-test for a particular power supply voltage has failed.
Nearest Agilent Technologies sales or service office
Burst generator memory failed. Modulation data produced by
321
Out of memory ARB communication failed
Out of memory Could not copy current istate
Out of memory Histogram display cannot function
Out of memory Memory allocation error
Out of memory Object Memory Area
Instrument is still functional
Lost. The meaning of this error is device-dependent
320
315
Protected user data saved by the *PUD command has been lost
Non-volatile data saved by the *SAV? command has been lost
An error was detected in the device’s memory
Values
System error File Not Found
To -200 Execution Errors
285
When parsing a downloaded program is device-specific
284
Illegal
Due to an error within the macro definition see Ieee 488.2
Command header, or contained invalid header syntax
Attempted. The definition of a math error is device-specific
276
An illegal memory subsystem name was used after the @
filename of was specified. This is not a legal filename
File name error Illegal filename character
File name not found SYSTEMFCDMA2KCHANFILE
Definition of what constitutes full media is device-specific
254
Catalog. Afterwards, try again
Try again
252
Sales or service office
What constitutes missing media is device-specific
250
Measurement accuracy is questionable
Data corrupt or stale filename
Algorithm. a potential cause is a failing backup battery
During the first power up after downloading new firmware into
Eeprom master copy if one exists. The system automatically
226
Memory or related device-specific requirements
223
To -200 Execution Errors
Too much data User filter has too many symbols
Data out of range Synthesizer Frequency out of bounds
Data out of range value clipped to upper limit
To -200 Execution Errors
All digital modulation multicarriers must be the same format
To -200 Execution Errors
ESG Family Signal Generators
Settings conflict Edge Bert requires Normal as Timeslot Type
Settings conflict FM & PM not allowed
Settings conflict GSM Bert requires Normal as Timeslot Type
ESG Family Signal Generators
Settings conflict I/Q & AM WB cannot be on at the same time
ESG Family Signal Generators
To -200 Execution Errors
Used in RC3 and 4 for channel
Used in RC1
To -200 Execution Errors
ESG Family Signal Generators
Error
For errors -221 through
Manual mode is on and therefore the instrument cannot sweep
220
212
Have described the error that is stalling list/sweep
Ignored
211
Execution Error Cannot update FlexDG with Even Second Delay
To -100 Command Errors
Specified filename exceeds the maximum length
Detect a more specific error
Device cannot detect a more specific error
150
148
Header contains more than twelve characters see Ieee 488.2
110Command header error
Syntax error
Invalid file name
201 to 702 Device-Specific Errors
User has attempted to write to a read-only memory subsystem
State file is not readable and the recall was aborted
Internal error report to factory
Synthesizer is unlocked. Service may be needed
Instrument’s output is unleveled
513 1 GHz Oscillator unlocked
Calibration failure Dcfm DC overrange
Reverse Power Protection RPP Tripped
DSP FW download failed Demodulator board
DSP times out Demodulator communication failed
Option 300 DSP for Bert capability returns an error
Configuration Error Option reconfiguration failed
Configuration error Installed board not supported
Configuration error OPTION, Invalid inconsistent license key
Option UN7 hardware has an invalid revision of Fpga code
Demodulator board has an invalid revision of DSP boot code
Fpga download failed Demodulator board
Modulation must have at least two states specified
filter must have at least one coefficient specified
Burst shape file is corrupted, or is not in the proper format
file is either corrupt or is not a FIR file
Top
Page
Image
Contents
