ESG Family Signal Generators | Agilent Technologies E4400-90333

ESG Family Signal Generators

-299 to -200: Execution Errors

Settings conflict; Pulse modulation cannot be on with internal burst.

There is a hardware conﬂict between pulse modulation and internal burst. The most recently requested modulation is turned on, the previous modulation is turned off.

Settings conflict; Pulse period set less than pulse width. Pulse width changed to match period value.

A pulse period has been entered that is smaller than the pulse width. The instrument automatically adjusts the pulse period to match the pulse width.

Settings conflict; The puncture rate is >=100% on DCH channel <NUMBER>, increase the DPCH Slot Format or edit the DCH fields to reduce the puncture %. All DPCH channels were turned off.

Transport channels cannot be punctured more than 100%. The slot format needs to be increased (which in turn increased the symbol rate) on the underlying DPCH channel, or the transport channel parameters must be changed to reduce the puncture percentage. The underlying DPCH channel has been turned off.

Settings conflict; QPCH and FFCH/OCNS cannot be on at the same time. FFCH/OCNS has been tuned off.

QPCH is generated using both channel 3 and 4. Channel 4 is now used to generate QPCH. Channel 3 can no longer generate FFCH/OCNS therefore, FFCH/OCNS must be turned off.

Settings conflict; RACH is only defined for Radio Configuration 1 and 2. You must set one of these Radio Configurations before configuring or using this code channel.

An attempt was made to setup the R-ACH while in a radio conﬁguration that does not support this channel. This channel is only available in RC1 and RC2. If the R-ACH is the desired channel, you must change to the proper radio conﬁguration before continuing.

Settings conflict; RCCCH is only defined for Radio Configuration 3 and 4. You must set one of these Radio Configurations before configuring or using this code channel.

An attempt was made to setup the R-CCCH while in a radio conﬁguration that does not support this channel. This channel is only available in RC3 and RC4. If the R-CCCH is the desired channel, you must change to the proper radio conﬁguration before continuing.

Error Messages

41

Image 43

Agilent Technologies E4400-90333 manual ESG Family Signal Generators

Contents

Supersedes February Copyright 1999-2001 Agilent Technologies Afﬁx Label Here Part No. E4400-90333 Contents Introduction Error Message Format Error Message Types No Error To -400 Query Errors Device has detected a failure during its self-test procedure To -300 Device-Speciﬁc Errors 321 Nearest Agilent Technologies sales or service ofﬁceSelf-test for a particular power supply voltage has failed. Burst generator memory failed. Modulation data produced by Out of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area 315 Lost. The meaning of this error is device-dependentInstrument is still functional 320 Values Non-volatile data saved by the *SAV? command has been lostProtected user data saved by the *PUD command has been lost An error was detected in the device’s memory System error File Not Found To -200 Execution Errors Illegal When parsing a downloaded program is device-speciﬁc285 284 276 Command header, or contained invalid header syntaxDue to an error within the macro deﬁnition see Ieee 488.2 Attempted. The deﬁnition of a math error is device-speciﬁc An illegal memory subsystem name was used after the @ ﬁlename of was speciﬁed. This is not a legal ﬁlename File name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE Try again 254Deﬁnition of what constitutes full media is device-speciﬁc Catalog. Afterwards, try again 250 Sales or service ofﬁce252 What constitutes missing media is device-speciﬁc Measurement accuracy is questionable Data corrupt or stale filename 226 During the ﬁrst power up after downloading new ﬁrmware intoAlgorithm. a potential cause is a failing backup battery Eeprom master copy if one exists. The system automatically Memory or related device-speciﬁc requirements 223 To -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC3 and 4 for channel Used in RC1 To -200 Execution Errors ESG Family Signal Generators 220 For errors -221 throughError Manual mode is on and therefore the instrument cannot sweep 211 Have described the error that is stalling list/sweep212 Ignored Execution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length 148 Device cannot detect a more speciﬁc errorDetect a more speciﬁc error 150 Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error Invalid ﬁle name 201 to 702 Device-Speciﬁc Errors User has attempted to write to a read-only memory subsystem State ﬁle is not readable and the recall was aborted Internal error report to factory Synthesizer is unlocked. Service may be neededInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Option UN7 hardware has an invalid revision of Fpga code Demodulator board has an invalid revision of DSP boot code Fpga download failed Demodulator board Modulation must have at least two states speciﬁed ﬁlter must have at least one coefﬁcient speciﬁed Burst shape ﬁle is corrupted, or is not in the proper format ﬁle is either corrupt or is not a FIR ﬁle