Agilent Technologies N6700 manual Supplemental Characteristics

Specifications Appendix A

Supplemental Characteristics

	N6751A / N6752A			N6753A	N6754A	N6761A / N6762A
Programming Ranges:
Voltage high range	20 mV – 51 V			10 mV – 20.4V	25 mV- 61.2V	15 mV – 51 V
Voltage low range (≤ 5.5 V)	N/A			N/A	N/A	12 mV – 5.5 V
Current high range	10 mA – 5.1A/10 mA- 10.2A			50 mA – 51A	20 mA- 20.4A	1 mA–1.53 A/1 mA–3.06 A
Current low range (≤ 0.1 A)	N/A			N/A	N/A	0.1 mA – 0.1 A NOTE 1
Programming Resolution:
Voltage high range	3.5 mV			1.5 mV	4.2 mV	880 μV
Voltage low range (≤ 5.5 V)	N/A			N/A	N/A	90 μV
Current high range	3.25 mA			16.3 mA	6.5 mA	60 μA
Current low range (≤ 0.1 A)	N/A			N/A	N/A	2 μA
Measurement Resolution:
Voltage high range	1.8 mV			0.8 mV	2.2 mV	440 μV
Voltage low range (≤ 5.5 V)	N/A			N/A	N/A	44 μV
Current high range	410 μA			2.05 mA	0.82 mA	30 μA
Current low range (≤ 0.1 A)	N/A			N/A	N/A	1 μA
200 μA current range (Option 2UA)	N/A			N/A	N/A	2 nA
Programming Temperature Coefficient per °C:
Voltage high range	18 ppm + 160 μV			20 ppm + 20 μV	20 ppm + 50 μV	18 ppm + 140 μV
Voltage low range (≤ 5.5 V)	N/A		A	N/A	N/A	40 ppm + 70 μV
Current high range	100 ppm + 45			60ppm + 500 μA	60ppm + 200 μA	33 ppm + 10 A
		μ				μ
Current low range (≤ 0.1 A)	N/A			N/A	N/A	60 ppm + 1.5 μA
Measurement Temperature Coefficient per °C:
Voltage high range	25 ppm + 35 μV			20 ppm + 20 μV	20 ppm + 50 μV	23 ppm + 40 μV
Voltage low range (≤ 5.5 V)	N/A			N/A	N/A	30 ppm + 40 μV
Current high range	60 ppm + 3 μA			60 ppm + 30 μA	60 ppm + 12 μA	40 ppm + 0.3 μA
Current low range (≤ 0.1 A)	N/A			N/A	N/A	50 ppm + 0.3 μA
200 μA current range (Option 2UA)	N/A			N/A	N/A	100 ppm + 3 nA/°C
Output Ripple and Noise: (PARD)
CC rm:	2 mA			10 mA	4 mA	2 mA

Common Mode Noise: (from 20 Hz – 20 MHz; from either output to chassis)

rms	500 μA	500 μA	750 μA	500 μA
peak-to-peak	< 2 mA	< 2 mA	< 3 mA	< 2 mA
Over-voltage Protection:
Accuracy	0.25% + 0.25 V	0.25% + 0.45V	0.25% + 0.6V	0.25% + 0.25 V
Maximum setting	55 V	22 V	66 V	55 V
Response time	50 μs from occurrence of over-voltage condition to start of output shutdown

Remote Sense Capability:

Outputs can maintain specifications with up to a 1-volt drop per load lead.

Series and Parallel Operation:

Identically rated outputs can be operated directly in parallel or be connected for straight series operation. Auto-series and auto-parallel operation is not available.

1If you are operating the unit below 255 μA in constant current mode, the output may become unregulated with the following load conditions: The load resistance is <175 mΩ and the load inductance is >20 μH. If this occurs, an UNRegulated flag will be generated and the output current may rise above the programmed value but will remain less than 255 μA.

Series N6700 User’s Guide 77