OmniSwitch 6600 Series Chassis and Hardware Components | Status LEDs |
|
|
|
|
Status LEDs
LEDs provide visual status information. These “status lights” are used to indicate conditions such as hardware and software status, primary and back up power supply status, primary and secondary status (stacked configurations), temperature and fan errors, slot number information, link integrity, and data flow.
Refer to the diagram below for detailed information on OmniSwitch 6600 series LED states.
Note. OmniSwitch 6600 series switches offer the same LED status indicators. For information on uplink module LEDs, refer to page
Slot Indicator LED
The slot indicator LED is manually configurable and displays the switch’s current slot number in a stacked configuration (i.e., 1 – 8). For detailed information on manually setting the switch’s slot number, refer to Chapter 3, “Managing OmniSwitch 6600 Series Stacks.”
|
| 25 | 27 | 29 | 31 | 33 | 35 |
TM OmniSwitch 6648 |
|
|
|
|
| ||
| CONSOLE |
|
|
|
|
|
|
|
| 26 | 28 | 30 | 32 | 34 | 36 |
|
| 1 | 3 | 5 | 7 | 9 | 11 |
OK1 | PS1 PRI TEMP |
|
|
|
|
|
|
OK2 | PS2 SEC FAN | SEL |
|
|
|
|
|
|
| 2 | 4 | 6 | 8 | 10 | 12 |
Ethernet Port LEDs
Each Ethernet port has a
LED Location | 45 | 47 |
|
|
37 | 39 | 41 | 43 | 45 | 47 |
|
|
|
|
|
|
| LINK/ACT | LINK/ACT |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| EXPANSION/STACKING | ||||||||
|
|
|
|
|
| 49 | 50 | 5 1 |
|
|
| 5 2 |
|
|
| |||
38 | 40 | 42 | 44 | 46 | 48 | |||||||||||||
| EXPANSION |
|
|
|
|
|
|
|
|
|
| |||||||
13 | 15 | 17 | 19 | 21 | 23 |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| LINK/ACT | LINK/ACT | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
14 | 16 | 18 | 20 | 22 | 24 |
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware and Software | Power Supply LEDs |
| Stack LEDs | Temperature | Management | |||||||
Status LEDs |
|
|
| PS1. | Displays | solid | green | PRI. Displays solid green | LEDs |
|
| |
OK1. Hardware Status. Dis- | when the primary (i.e., factory- | when if the switch is either a | TEMP. Displays solid | green | ||||||||
plays solid green when pow- | installed) power supply status | when the switch is operating | ||||||||||
ered on and the switch has | is OK and the power supply is | mary switch in a stack; other- | within the allowed temperature | |||||||||
passed | hardware | diagnostic | operating normally. Displays | wise, if the switch status is | range; displays solid amber if a | |||||||
tests. | Displays solid | amber | solid amber in the unlikely | secondary or idle, this LED is | temperature error occurs (i.e., | |||||||
when powered on and the | event of a power supply fail- | off. | the switch is operating outside | |||||||||
switch | has | failed | hardware | ure. |
|
|
| SEC. Displays solid green if | the temperature range). |
| ||
diagnostic tests. |
|
| PS2. |
|
|
| FAN. Displays | solid | green | |||
OK2. Software Status. Blinks | Displays | solid | green | the switch is the secondary | ||||||||
when | the optional redundant | switch in a stack; otherwise, | when all fans in the fan tray | |||||||||
green when the switch’s sys- | power supply status is OK and | this LED is off. | are running at normal speed. | |||||||||
tem management software is | the power supply is operating |
| Displays solid amber if a fan | |||||||||
operational. | Displays | solid | normally. Displays solid amber |
| error occurs (i.e., one or more | |||||||
amber when a system soft- | if no redundant power supply |
| fans are not running at normal | |||||||||
ware | failure | occurs. | Blinks | is installed or in the unlikely |
| speed). |
|
| ||||
amber when the software is in | event of a redundant power |
|
|
|
| |||||||
a transitional state (e.g., when | supply failure. |
|
|
|
|
|
| |||||
software is being downloaded |
|
|
|
|
|
|
|
| ||||
to the switch). |
|
|
|
|
|
|
|
|
|
| ||
Front Panel LED Descriptions (OS6648 Shown)
OmniSwitch 6600 Series Hardware Users Guide April 2004 | page |
