Troubles shooting | Allied Telesis AT-IFS802SP instruction

72	AT-IFS802SP-80 User Manual

Troubles shooting

•Verify that is using the right power cord/adapter (DC 24-48V), please don’t use the power adapter with DC output higher than 48V, or it may damage this device.

•Select the proper UTP/STP cable to construct the user network. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections that depend on the connector type the switch equipped: 100Ω Category 3, 4 or 5 cable for 10Mbps connections, 100Ω Category 5 cable for 100Mbps connections, or 100Ω Category 5e/above cable for 1000Mbps connections.

Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).

•Diagnosing LED Indicators:To assist in identifying problems, the switch can be easily monitored through panel indicators, which describe common problems the user may encounter and where the user can find possible solutions.

•If the power indicator does not light on when the power cord is plugged in, you may have a problem with power cord. Then check for loose power connections, power losses or surges at power outlet. If you still cannot resolve the problem, contact the local dealer for assistance.

•If the LED indicators are normal and the connected cables are correct but the packets still cannot be transmitted. Please check the user system’s Ethernet devices’ configuration or status.

Image 76

Allied Telesis AT-IFS802SP manual Troubles shooting

Contents

AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features Introduction CSMA/CD Software Features Snmp MIB Package Contents Hardware Description Physical DimensionFront Panel Top View LED Indicators LED Hardware Installation Installation Steps DIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring Application Coupling Ring Application Dual Homing Application Console Management Connecting to the Console PortPin Assignment Login in the Console Interface CLI Management Commands Level Exec System Login Web-Based ManagementAbout Web-based Management Preparing for Web Management System Information IP Configuration System configuration Dhcp Server Client Entries Port and IP Bindings Restore Configuration Update FirmwareTftp Syslog Configuration Backup ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port Statistics Port Control Aggregator setting Port Trunk State Activity tab Lacp disabled Aggregator Information Lacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning Tree Port Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority Type Port-based Priority COS Configuration Igmp ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration 802.1x System Configuration interface MAC Address Table Misc ConfigurationStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Multicast Filtering interface Save Configuration Factory DefaultSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands Set Password Low IPHigh IP Subnet mask Port Commands Set PortidDuplex full half 101001000auto State Enable Disable Trunk Commands Set Vlan Commands Set Vlan 8021q trunk Spanning Tree Commands Set ~61440Seconds Time seconds AutoTrueFalse Port PriorityTrueFalse Commands Set Igmp enable Igmp-query autoIgmp-query force Show igmp Mac-address-table Static hwaddrFilter hwaddr Show mac-address Authentication Password Privacy V1v2cv3v1v2cv3Strings Community Community-string ExcludedIncluded View NameHost-address RXTXBoth Words Port IDSec Disable reject Accept authorize Backup FlashbackupcfgRestore Flashrestorecfg SystemLog, Smtp and Event Commands Set No event authentication FailureNo event ring-topology Change Sntp Commands Set Start time End timeMinute Timezone Control Port Ring Commands SetDual Homing Port