Igmp enable, Igmp-query auto, No igmp | Allied Telesis AT-IFS802SP

86	AT-IFS802SP-80 User Manual

IGMP Commands Set


	Netstar Commands	Level	Description	Example

	igmp enable	G	Enable IGMP snooping	switch(config)#igmp enable
	igmp enable	G	function	switch(config)#igmp enable
			function

	Igmp-query auto	G	Set IGMP query to auto	switch(config)#Igmp-query auto
	Igmp-query auto	G	mode	switch(config)#Igmp-query auto
			mode
	Igmp-query force	G	Set IGMP query to force	switch(config)#Igmp-query force
	Igmp-query force	G	mode	switch(config)#Igmp-query force
			mode

	show igmp	P	Displays the details of an	switch#show igmp configuration
	configuration	P	IGMP configuration.	switch#show igmp configuration
	configuration		IGMP configuration.
	no igmp	G	Disable IGMP snooping	switch(config)#no igmp
	no igmp	G	function	switch(config)#no igmp
			function

	no igmp-query	G	Disable IGMP query	switch#no igmp-query

Image 90

Allied Telesis AT-IFS802SP manual Igmp enable, Igmp-query auto, Igmp-query force, Show igmp, No igmp-query

Contents

AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features Introduction CSMA/CD Software Features Snmp MIB Package Contents Physical Dimension Hardware DescriptionFront Panel Top View LED Indicators LED Hardware Installation Installation Steps DIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring Application Coupling Ring Application Dual Homing Application Connecting to the Console Port Console ManagementPin Assignment Login in the Console Interface CLI Management Commands Level Exec About Web-based Management System LoginWeb-Based Management Preparing for Web Management System Information IP Configuration System configuration Dhcp Server Client Entries Port and IP Bindings Update Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port Statistics Port Control Aggregator setting Port Trunk State Activity tab Lacp disabled Aggregator Information Lacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning Tree Port Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority Type Port-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration 802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast Filtering Multicast Filtering interface Factory Default Save ConfigurationSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments 10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands Set High IP PasswordLow IP Subnet mask Duplex full half Port Commands SetPortid 101001000auto State Enable Disable Trunk Commands Set Vlan Commands Set Vlan 8021q trunk Seconds Spanning Tree Commands Set~61440 Time seconds Port Priority AutoTrueFalseTrueFalse Commands Set Igmp-query force Igmp enableIgmp-query auto Show igmp Filter hwaddr Mac-address-tableStatic hwaddr Show mac-address Strings Community Authentication Password PrivacyV1v2cv3v1v2cv3 Community-string View Name ExcludedIncludedHost-address RXTXBoth Port ID WordsSec Disable reject Accept authorize Restore BackupFlashbackupcfg Flashrestorecfg SystemLog, Smtp and Event Commands Set No event ring-topology No event authenticationFailure Change Minute Sntp Commands SetStart time End time Timezone Ring Commands Set Control PortDual Homing Port