Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-IFS802SP manual Lacp enabled

Models: AT-IFS802SP

1 101

Download 101 pages 49.51 Kb

Page 49

AT-IFS802SP-80 User Manual

45

•LACP enabled

Having set up the aggregator setting with LACP enabled, you will see the trunking group information between two switches on the tab of Aggregator Information.

Switch 1 configuration

1.Set System Priority of the trunk group.The default is 1.

2.Select a trunk group ID by pull down the drop-down menu bar.

3.Enable LACP.

4.Include the member ports by clicking the Add button after selecting the port number and the column field of Work Ports changes automatically.

Switch 1 configuration interface

Aggregation Information of Switch 1

5.Click on the tab of Aggregator Information to check the trunked group information as the illustration shown above after the two switches configured.

Image 49

Allied Telesis AT-IFS802SP manual Lacp enabled

Contents

AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Hardware Description Physical DimensionFront Panel Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Console Management Connecting to the Console PortPin Assignment CLI Management Login in the Console InterfaceExec Commands LevelWeb-Based Management System LoginAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesRestore Configuration Update FirmwareTftp Syslog Configuration Backup ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority COS Configuration Igmp ConfigurationTOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface MAC Address Table Misc ConfigurationStatic MAC Address MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface Save Configuration Factory DefaultSystem Reboot Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsLow IP PasswordHigh IP Subnet maskPortid Port Commands SetDuplex full half 101001000autoDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk ~61440 Spanning Tree Commands SetSeconds Time secondsAutoTrueFalse Port PriorityTrueFalse Commands Set Igmp-query auto Igmp enableIgmp-query force Show igmpStatic hwaddr Mac-address-tableFilter hwaddr Show mac-addressV1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-stringExcludedIncluded View NameHost-address RXTXBoth Words Port IDSec Accept authorize Disable rejectFlashbackupcfg BackupRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set Failure No event authenticationNo event ring-topology ChangeStart time End time Sntp Commands SetMinute TimezoneControl Port Ring Commands SetDual Homing Port