Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-IFS802SP manual Vlan Port Based interface

Models: AT-IFS802SP

1 101

Page 55

AT-IFS802SP-80 User Manual

			VLAN – Port Based interface
•	Pull down the selection item and focus on Port Based then press
•				Apply	to set the VLAN
	Operation Mode in Port Based mode.
•	Click	Add	to add a new VLAN group (The maximum VLAN groups are up to 64).

VLAN—Port Based Add interface

•Enter the group name and VLAN ID. Add the selected port number into the right field to group these members to be a VLAN group, or remove any of them listed in the right field from the VLAN.

•And then, click Apply to have the configuration take effect.

•You will see the VLAN list displays.

Page 55

Image 55

Allied Telesis AT-IFS802SP manual Vlan Port Based interface

Contents

AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Hardware Description Physical DimensionFront Panel Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Console Management Connecting to the Console PortPin Assignment CLI Management Login in the Console InterfaceExec Commands LevelPreparing for Web Management System LoginWeb-Based Management About Web-based ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesRestore Configuration Update FirmwareTftp Syslog Configuration Backup ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority COS Configuration Igmp ConfigurationTOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface MAC Address Table Misc ConfigurationStatic MAC Address MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface Save Configuration Factory DefaultSystem Reboot Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsSubnet mask PasswordLow IP High IP101001000auto Port Commands SetPortid Duplex full halfDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Time seconds Spanning Tree Commands Set~61440 SecondsAutoTrueFalse Port PriorityTrueFalse Commands Set Show igmp Igmp enableIgmp-query auto Igmp-query forceShow mac-address Mac-address-tableStatic hwaddr Filter hwaddrCommunity-string Authentication Password PrivacyV1v2cv3v1v2cv3 Strings CommunityExcludedIncluded View NameHost-address RXTXBoth Words Port IDSec Accept authorize Disable rejectFlashrestorecfg BackupFlashbackupcfg RestoreSystemLog, Smtp and Event Commands Set Change No event authenticationFailure No event ring-topologyTimezone Sntp Commands SetStart time End time MinuteControl Port Ring Commands SetDual Homing Port

VLAN – Port Based interface