12-EN
01GB06PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From a PC
Adjust the Front and Rear speaker volume (Initial setting: “0”).
Setting contents: F (Front) 15 to C (Center) 0 to R (Rear) 15
Adjust the Right and Left speaker volume (Initial sett ing: “0”).
Setting contents: L (Left) 15 to C (Center) 0 to R (Right) 15
Adjust the subwoofer output (Initial setting: “0”).
Setting contents: 0 to 15
•This has no effect when the subwoofer is off.
Adjust the volume. (Initial setting: “-INF. dB”)
1
Drag [ ] or click [ ] or [ ] to make adjustments.
Pressing and holding [ ] or [ ] will continuously
decrease/increase volume.
Setting contents: -INF. to 0 dB
Setting Defeat
When Defeat is set to [ON], the settings for ImprintEQ, Graphic EQ,
Parametric EQ, MX Plus, RoadEQ, and Time Collection are restored to
the initial values (Initial setting: “OFF”).
1
Click [ON] or [OFF] for “Defeat” in the main menu.
Switching the Sources
The unit accepts up to five analog signal input lines and 2 digital signal
input lines. For the connection, refer to the installation manual.
When an Ai-NET compatible head unit is connected, the source should
be switched at the head unit.
1
Click [ ] for “Source” in the main menu and select
and click the source you want from the pull-down
menu.
The source is switched to the selected one.
Setting contents:Auxiliary*(AUX1)/Auxiliary(AUX2)/
Auxiliary(AUX3)/Auxiliary(Ai-NET(HU))/
Auxiliary(Ai-NET(CHG))/Auxiliary(Digital1)/
Auxiliary(Digital2)
* Names selected in “Naming the AUX Input (AUX Name)” (page16)
are displayed as the source names. The initial setting is “Auxiliary.”
•The number of analog signal inputs varies depending on the setting
in “Setting the AUX Input System (AUX Input System Select)”
(page14).
•Only sources set as ON in “Setting the AUX Input (AUX IN)”
(page15) and “Setting the Digital Input (Digit al AUX)” (page15)
are displayed.
Storing the Preset Values (Preset Store)
You can store up to 6 sets of the adjustment/setting values. All of the
following adjustment/setting values are stored in a sin gle preset
memory.
1
Adjust the value you want to store and set it.
2
Click [Store] for “Preset” in the main menu.
Adjusting Fader (Between Front and Rear)
Adjusting Balance (Between Left and
Right)
Adjusting Subwoofer (SubW Lv)
Adjusting Volume Adjustment/Setup items Pages
Setting the Speaker System (Output System Select) 13
Setting the Speakers (Speaker Setup)/Setting the
Subwoofers
14
Setting the AUX Input System (AUX Input System Select) 14
Setting the AUX Input (AUX IN) 15
Setting the Digital Input (Digital AUX) 15
Setting the AUX Volume Input Level (AUX IN Gain) 15
Adjusting the AUX Volume Level (AUX Level) 15
Naming the AUX Input (AUX Name) 16
Turning ImprintEQ On/Off 19
Turning RoadEQ On/Off 21
Setting MX Plus (Ai-NET Mode) 22
Setting MX Plus (Standalone Mode) 22
Setting the Graphic EQ 23
Setting the Parametric EQ 25
Adjusting X-Over and Switching the Phases 26
Adjusting the Time Correction (TCR) 28
Setting the 2-Channel Signal Playback Mode (2ch
Playback Mode)
30
Setting EUPHONY (EUPHONY) 30
Using Dolby Pro Logic II (Dolby Pro Logic II) 31
Adjusting the Center Width (Center Width) 32
Adjusting the Speaker Volume Level (Output Level) 33
Adjusting the Acoustic Image (BI-PHANTOM) 33
Mixing the Low Range Audio for the Rear (Rear Mix) 33
Mixing the Low Range Audio of the Center with the Front
L/R (Center Base Split) 34
Setting the Linear PCM (PCM Mode) 34
Achieving Powerful High Volume Sound (Listening Mode) 34
Adjusting the DVD Level (DVD Level) 34
01GB00PXAH800.book Page 12 Tuesday, February 8, 2011 9:04 PM